EasyManua.ls Logo

Petsafe PIG00-10777 - User Manual

Petsafe PIG00-10777
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
stubborn dog
in-ground fence
™
operating and training guide
Model Number
PIG00-10777
PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING

Table of Contents

Questions and Answers

  • M
    Mrs. Kristy RobertsAug 12, 2025
    What to do if the Petsafe PIG00-10777 receiver collar activates inside the house?
    • L
      Lisa SaundersAug 13, 2025
      If the receiver collar activates inside the house, try the following: Turn the Boundary Width Control knob counterclockwise to decrease the activation distance. Ensure the Boundary Wire is at least 15 feet away from the house to prevent signal transmission through walls. Also, confirm that Boundary Wires are twisted from the boundary to the Fence Transmitter.
  • B
    bruceharryAug 16, 2025
    Why is Petsafe PIG00-10777 receiver collar not beeping or correcting?
    • R
      Ryan RobinsonAug 16, 2025
      If the receiver collar isn't beeping or correcting, first, check the battery to ensure it's properly installed. Next, verify that both lights are lit on the Fence Transmitter. If not, perform the “Transmitter Loop Test”.
  • C
    Cassandra PerryAug 20, 2025
    What to do if the Petsafe PIG00-10777 Pet Care Product power and loop indicator lights are off?
    • R
      Robert AlvarezAug 20, 2025
      If the power and loop indicator lights are off, check that the power adapter is correctly plugged into both the Fence Transmitter and the outlet. If plugged into a GFCI or RCD outlet, check and reset the circuit if needed. Verify the outlet's functionality by testing with a working item. Try a different 120-volt outlet. If issues persist without a surge protector, contact customer care for a replacement.
  • J
    joshuaandersonAug 25, 2025
    What to do if Petsafe PIG00-10777 Pet Care Product receiver collar has to be held on top of the boundary wire to activate?
    • T
      Taylor RobinsonAug 25, 2025
      If the receiver collar needs to be held on top of the boundary wire to activate, try these steps: Replace the battery. Adjust the Boundary Width Control knob clockwise to increase the activation distance. Ensure the Boundary Control Switch is properly set for the amount of Boundary Wire used. If using a Double Loop, ensure the Boundary Wires are separated by at least 5 feet. If the issue persists, perform the “System Test” and/or “Transmitter Loop Test.”
  • E
    evansbrianAug 27, 2025
    What to do if the Petsafe Pet Care Product power light is on, but the loop indicator light is off, and the fence transmitter loop alarm is sounding?
    • M
      Meghan ThompsonAug 27, 2025
      If the power light is on, the loop indicator light is off, and the fence transmitter loop alarm is sounding, check the Boundary Wire connections at the Fence Transmitter to ensure they are properly connected. Also, inspect for any broken or damaged Boundary Wires where they enter the house. Perform the “Transmitter Loop Test” to see if the Fence Transmitter needs replacing. If the transmitter works, there's likely a break in your Boundary Wire; consult the “Wire Break Location Test” section of the guide.
  • J
    Joseph CuevasAug 31, 2025
    What to do if the Petsafe Pet Care Product receiver collar is beeping, but the pet is not responding to the static correction?
    • J
      Jeremiah BrownAug 31, 2025
      If the receiver collar is beeping but your pet isn't responding to the static correction, test the receiver collar with the test light while walking toward the boundary wire. If the test light flashes, check the collar's fit. Trim your pet's fur where the contact points touch the neck, and consider purchasing longer contact points. Increase the static correction level and repeat training steps.
  • J
    Jennifer GordonSep 4, 2025
    Why do I have an inconsistent signal with my Petsafe PIG00-10777?
    • A
      Adam PattersonSep 4, 2025
      For an inconsistent signal, ensure the Fence Transmitter is at least 3 feet away from large metal objects or appliances. Make sure all Boundary Wire turns are gradual, with a minimum 3-foot radius. Ensure the Boundary Wire isn't running parallel to and within 10 feet of electrical wires, neighboring containment systems, telephone wires, television or antenna cables, or satellite dishes. If a neighboring containment system is the cause, move the Boundary Wire farther away from it.
  • K
    Kelly MackSep 8, 2025
    How to reset the low battery indicator on Petsafe PIG00-10777 Pet Care Product?
    • H
      hendersonanthonySep 8, 2025
      To reset the low battery indicator, remove the battery from the receiver collar. Discharge all power by holding the correction level button down until the light is no longer illuminated, then reinstall the battery.

Summary

Important Safety Information

How the System Works

Operating Guide

Locate the Fence Transmitter

Lay Out the System

Position the Boundary Wire

Connect the Wires to the Fence Transmitter

Prepare the Receiver Collar

Covers battery insertion, removal, and setting the static correction level.

Set the Boundary Width and Test the Receiver Collar

Instructions for adjusting containment field width and testing system functionality.

Install the Boundary Wire

Fit the Receiver Collar

Proper fitting and adjustment of the receiver collar on the pet.

Training Guide

Be Patient With Your Pet

Boundary Awareness

Continue Boundary Awareness

Distraction Phase

Unleashed Supervision

Troubleshooting

System Test

Detailed procedure to diagnose system problems using a test loop wire.

Transmitter Loop Test

Method to identify boundary wire or transmitter issues using a test loop.

Wire Break Location Test

Steps to find breaks or damage in the boundary wire.

Petsafe PIG00-10777 Specifications

General IconGeneral
Product TypeWireless Fence
Coverage AreaUp to 1/2 acre
WaterproofYes
Number of PetsUnlimited with additional collars
BrandPetSafe
Model NumberPIG00-10777
ColorBlack
Intended UsePet Containment
Collar TypeReceiver Collar
Adjustable Levels of Correction5 levels of static correction
Battery TypeRFA-67
MaterialPlastic

Related product manuals