Petsafe Stay & Play PIF00-13663 User Manual (English)

Questions and Answers:

L
Lindsey RobertsAug 17, 2025
What to do if my Petsafe Stay & Play PIF00-13663 Pet Care Product receiver collar is not sounding or administering a static correction?
- J
  Jamie MorrisonAug 17, 2025
  First, ensure that the transmitter is properly connected to a working 120-volt outlet and is turned on. Check that the power light is illuminated and that the transmitter controls are set to your desired levels. Also, verify that the receiver collar is powered on and that the battery status lights are flashing every 4-5 seconds. If not, try charging the receiver collar.
A
Andrew GarrisonAug 19, 2025
How to fix Petsafe Stay & Play PIF00-13663 Pet Care Product transmitter when the power light is not on?
- M
  mbartlettAug 19, 2025
  Make sure the power adapter is properly plugged into a working 120-volt wall outlet. Test the outlet by plugging in another device, such as a radio, to ensure it's functioning correctly. If the power light remains off, the fence transmitter or power adapter may need replacement.
B
Brandon ForbesAug 22, 2025
How to troubleshoot a Petsafe Pet Care Product when the receiver collar tone isn't sounding during boundary setup?
- B
  Bryce GlennAug 22, 2025
  First, ensure the receiver collar is on and the battery status lights flash every 4-5 seconds, or charge the collar. The tone might be hard to hear in a noisy area. Use the test light as explained in its section to find the boundary zone. Also, check the transmitter setup.
P
Pam CisnerosAug 25, 2025
What to do if the Petsafe Stay & Play PIF00-13663 Pet Care Product receiver collar tone is sounding, but my pet isn't responding to the static correction?
- J
  Jeff RobinsonAug 26, 2025
  Ensure the static correction level is set to 2 or higher. Test the receiver collar using the test light. If the test light flashes, check how the receiver collar fits. Trim your pet's fur where the contact points touch the neck or switch to longer contact points. You might also need to increase the static correction level or repeat training steps to reinforce learning.
M
matthew47Aug 28, 2025
Why is my Petsafe Pet Care Product receiver collar tone sounding inside the house?
- P
  Paul MercerAug 28, 2025
  To prevent accidental activation, it's recommended to remove the receiver collar from your pet when they are indoors. Also, ensure the transmitter is on and properly set up according to the instructions. Check that the entire house is within the designated pet area; you might need to move the transmitter to include the whole house. If you relocate the transmitter, take off the receiver collar before turning the transmitter off.
D
Danny KimAug 30, 2025
What should I do if my pet is fearful of the static correction from the Petsafe Stay & Play PIF00-13663 Pet Care Product?
- N
  Nicole CooleyAug 31, 2025
  Lower the static correction level. Ensure you are in control during the first static corrections by using a leash attached to a non-metallic collar, guiding your pet into the pet area, and offering praise. If fear persists, pause training and resume the next day. Always conclude training with praise and play.
A
abigail99Sep 2, 2025
Why does my Petsafe Stay & Play PIF00-13663 receiver collar activate in the middle of the yard?
- S
  Shirley BrightSep 2, 2025
  The receiver collar may activate when it loses the transmitter signal, which can happen if a large metal object is between the receiver collar and transmitter, if the receiver collar's orientation changes near the boundary zone, or if there's electronic interference. If this continues, consider moving the transmitter and resetting the pet area.
T
Tyler RamirezSep 4, 2025
Why is the Petsafe Pet Care Product receiver collar tone sounding everywhere?
- J
  Joshua RodriguezSep 4, 2025
  Check that the transmitter is properly plugged into a working standard 120-volt outlet, turned on, the power light is on, and the transmitter controls are set at your desired settings.
A
Amy PooleSep 7, 2025
Why is my pet getting static correction in his metal crate from the Petsafe Pet Care Product?
- J
  Jessica TurnerSep 7, 2025
  The receiver collar activates when it loses the transmitter signal. A metal crate can block the transmitter signal, causing the receiver collar to activate. Remove the receiver collar from your pet when placing him in the metal crate.
M
Marvin WhiteSep 12, 2025
Why doesn't my Petsafe Pet Care Product receiver collar activate near my neighbor's containment system?
- V
  vheathSep 12, 2025
  Your neighbor's containment signal might interfere with the operation of the receiver collar, preventing activation near their fence. To reduce interference, decrease the size of your pet area or move the transmitter away from your neighbor's system. Adjust the pet area so the receiver collar activates at least 5 feet beyond the reduced boundary when approaching the neighboring system.

Petsafe Stay & Play PIF00-13663 Specifications

General

Type	Wireless Fence System
Model Number	PIF00-13663
Battery Type	RFA-67 battery
Static Correction Levels	5 levels
Waterproof	Yes
Receiver Collar	Included
Material	Plastic
Compatible Pets	Dogs
Coverage Area	Up to 3/4 acre
Collar Size	Adjustable, fits neck sizes 6 to 28 inches