Service Modes, Error Codes, and Fault Finding
EN 18 TPB1.1HU LA5.
2010-Nov-05
5.2 Software Upgrading
5.2.1 Introduction
Philips continuously tries to improve its products, and it’s
recommend that the TV software is updated when updates are
available. Software update files can be obtained from the
dealer or can be downloaded from the following websites:
http://www.philips.com/support
Preparing a portable memory for software upgrade
The following requirements have to be met:
1. A personal computer connected to the Internet.
2. An archive utility that supports the ZIP-format (e.g. WinZip
for Windows or Stufflt for Mac OS).
3. A USB flash drive (preferably empty).
Note:
1. Only FAT/DOS-formatted flash drives are supported.
2. Only use software update files that can be found on the
http://www.philips.com/support
web site.
5.2.2 Check the current TV software version
Before starting the software upgrade procedure, it is advised to
check that what the current TV software:
1. Press the “1 2 3 6 5 4” button on the remote control to enter
the CSM mode.
2. Use the left/right cursor keys to select “Software Versions”.
If the current software version of the TV is the same as the
latest update file found on http://www.philips.com/support
, it is
not necessary to update the TV software.
5.2.3 Download the latest software
1. Point the web browser to http://www.philips.com/support
.
2. Find information and software related to the TV.
3. Select the latest software update file and download it to the
PC.
4. Insert a USB flash drive into one of the USB ports of the
PC.
5. Decompress the downloaded ZIP file and copy the
software of back-end board, Smart module board and
Stand by to the root directory of the USB flash drive. E.g.
TVSoftwareUpgrade_BEvx.xx.upg for back-end board
software, TVSoftwareUpgrade_SMvx.xx.x.upg for smart
module board software,
TVSoftwareUpgrade_MCUvx.x.upg for smart module
board standy-by software.
5.2.4 Update the TV software
1. Insert mains power and wait for system to boot completely.
2. Insert the USB flash drive that contains the software
update files.
3. The TV will detect the USB flash drive automatically. Press
the “back” button on the remote control to exit it.
See Figure 5-7
.
4. Press “3 1 9 7 5 3 Mute” on the guest remote control or
Menu on setup remote control (Green/Yellow RC) , and
enter the “Setup Menu”. See Figure 5-8
.
5. Please select [TV Upgrade] > [Source] > [USB], and press
OK. See Figure 5-8
.
6. Please select [Direction] > [USB To TV], and press OK.
See Figure 5-8
.
7. Please select [Upgrade Type] > [Software Upgrade
Package], and press OK. See Figure 5-8
.
8. Please select [SW Version Check] > [Yes], and press OK.
See Figure 5-8
.
9. After finished the above setting, please select [Start], and
press right cursor on the remote control, a window will
display. See Figure 5-9
.
10. Use the up/down cursor keys to select the software that
needs to be upgraded, for example,
TVSoftwareUpgrade_BEvx.xx.upg for back-end board
software.
11. Press OK to start, then a window will display.
See Figure 5-10
.
12. Please select yes and press OK to continue the upgrading
process. See Figure 5-11
.
13. Upgrading now continues and the status of the updating
progress will be displayed.
14. When the TV software is updated, the TV will restart itself.
Figure 5-7 Update the TV software [1/5]
Figure 5-8 Update the TV software [2/5]
Figure 5-9 Update the TV software [3/5]
18890_206_100920.eps
101018
18890_207_100920.eps
101018
18890_208_100920.eps
101018
To Next Page
Loading...
