Configure bulb
In the following step, you will configure each
Philips hue bulb
.
To configure each hue bulb…
1 - Select the bulb name in the
Configure Ambilight+hue
menu
and press
OK
. The bulb you selected is blinking.
2 - First indicate where you placed the bulb relative to the TV. A
correct setting of the
Angle
will send the correct Ambilight
colour to the bulb. Press
(up) or
(down) to adjust.
3 - Press
(right) to set the distance.
4 - Secondly, indicate the
Distance
between the bulb and the
TV. The further away from the TV, the weaker the Ambilight
colour. Press
(up) or
(down) to adjust.
5 - Press
(right) to set the brightness.
6 - Finally, set the
Brightness
of the bulb. Press
(up) or
(down) to adjust.
7 - To stop configuring this bulb, select
OK
and press
OK
.
8 - In the
Configure Ambilight+hue
menu, you can select every
bulb and do the same.
9 - When all Ambilight+hue bulbs are configured, select
Finish
and press
OK
.
Ambilight+hue is ready for use.
You can always change the Ambilight+hue configuration later.
To change the configuration, press
and select
Setup
>
TV
settings
>
Ambilight
>
Ambilight+hue
.
Immersion
With
Immersion
, you can adjust the level of the Ambilight effect
for the Ambilight+hue bulbs.
To adjust the Ambilight+hue Immersion…
1 - Press
and select
Setup
and press
OK
.
2 - Select
TV settings
>
Ambilight
>
Ambilight+hue
>
Immersion
and press
OK
.
3 - Press
(up) or
(down) to adjust.
4 - Press
, repeatedly if necessary, to close the menu.
Info
In
View configuration
, you can consult the current
Ambilight+hue configuration. Which network you use, how
many bulbs are connected, etc.
To view the current Ambilight+hue setup…
1 - Press
and select
Setup
and press
OK
.
2 - Select
TV settings
>
Ambilight
>
Ambilight+hue
>
View
configuration
and press
OK
.
3 - Select the item you want to view and press
OK
.
4 - Press
,
repeatedly if necessary, to close the menu.
Advanced Ambilight settings
Wall colour
With
Wall colour
, you can neutralise the influence of a coloured
wall on the Ambilight colours. Select the colour of the wall
behind the TV and the TV will modify the Ambilight colours to
appear as they are intended.
To select the colour of the wall . . .
1 - Press
and select
Setup
and press
OK
.
2 - Select
TV settings
>
Ambilight
>
Advanced
>
Wall colour
.
3 - Select the colour sample that matches the colour of the wall
behind the TV and press
OK
.
4 - Press
, repeatedly if necessary, to close the menu.
TV switch off
With
TV switch off
, you can set Ambilight to switch off
immediately or slowly fade out when you switch off the TV. The
slow fade out gives you some time to switch on the lights in
your living room.
To select the TV switch off . . .
1 - Press
and select
Setup
and press
OK
.
2 - Select
TV settings
>
Ambilight
>
Advanced
>
TV switch
off
.
3 - Select
Fade out to off
or
Immediate switch off
.
4 - Press
, repeatedly if necessary, to close the menu.
Lounge light mood
When the TV is on standby, you can switch Ambilight on and
create a Lounge light effect in your room.
To switch Ambilight on while the TV is on standby, press
(Ambilight).
To change the Lounge light colour range, press
(Ambilight) again.
To switch off Lounge light, press and hold
(Ambilight) for a
few seconds.
You can also set up the colour range in the TV settings menu.
1 - Switch on the TV (out of the Lounge light mode).
2 - Press
and select
Setup
and press
OK
.
3 - Select
TV settings
>
Ambilight
>
Advanced
>
Lounge light
mood
and press
OK
.
4 - Select the colour range you prefer.
5 - Press
, repeatedly if necessary, to close the menu.
Lounge light+hue
If you installed Ambilight+hue, you can let the hue bulbs follow
Lounge light from Ambilight. The Philips hue lamps will expand
the Loung light effect across the room. The hue bulbs are
79
To Next Page
Loading...
