17
Basic Operation
1
Press SYSTEM MENU in the
STOP mode to enter the Setup
Menu.
2 Press the OK key to open the
next level submenu or confirm your selection.
3
Press the 1 2 keys to enter the submenu or
return to the previous menu.
4 Press the 34 keys to highlight the desired menu.
5 Press SYSTEM MENU to quit the setup menu.
➜ When you quit the setup menu, the settings
will be stored in the player’s memory even if the
player is switched to power off.
General Setup menu
Some settings are needed in this menu. They are:
DISC LOCK, PROGRAM, VFD DIM, OSD
LANGUAGE and SCREEN SAVER.
Follow the steps below:
1 Press the SYSTEM MENU key to enter the setup
menu.
2 Press the 34 keys to choose the GENERAL
SETUP.
3 Press the OK key to confirm selection.
Disc Lock
When the disc is locked, the player will store its
typical code into the memory for the future
identification. For the next playback, the DVD
player will prompt to enter the password. And
then, press OK to load the disc.
1 Press the 34 keys to highlight DISC LOCK in the
GENERAL SETUP menu.
2 Enter its submenu by pressing the 2 key.
➜ LOCK: Lock the disc being played.
➜ UNLOCK: unlock the disc.
3 Press the 1 key to return to the GENERAL
SETUP menu.
NOTE:
1. When a locked disc is loading, the DVD player
will prompt to enter your password (842100 is the
super password).
2. To change the password , refer to the option
PASSWORD in the PREFERENCE SETUP menu .
Program (not for Picture CD/MP3)
1 To choose PROGRAM, press 34 keys.
2
Press the 2 key to move the cursor to the field of
the submenu to choose the item ON.
➜ ON: Enter the PROGRAM item.
3 Press OK to enter the program page.
Input your favorite track
1 Input valid track number by pressing the
numerical keys.
2 Press the 1 234 keys to move the cursor to the
next selected position.
➜ If the track number is out of ten, press 2™ to
open the next page and go on programing, or
press 1 234 to highlight NEXT button, and then
press OK.
3
Repeat this steps to input another track number
until the whole program is completed.
Remove a track
1 Press the 1 234 keys to move the cursor to the
track you want to remove.
2 Press OK or PLAY key to remove this track from
the program menu.
Playback tracks
When programing is completed,
1 Press the 1 234 keys to move the cursor to the
START button.
2 Press OK.
➜ DVD player will playback the selected tracks
under the programed sequence.
Setup Menu
18
Setup Menu
OSD language
There are two options available for information
display on TV screen.
1 Press the 34 keys to highlight OSD
LANGUAGE in the GENERAL SETUP menu.
2 Enter its submenu by pressing the 2 key.
3 Move the cursor by pressing the 34 keys to
highlight the selected language.
4 Press the OK key to confirm.
5 Press the 1 key to return to the GENERAL
SETUP menu.
Screen Saver
This function is used to turn on or off the screen
saver.
1 Press the 34 keys to highlight SCREEN SAVER
in the GENERAL SETUP menu.
2 Enter its submenu by pressing the 2 key.
3 Move the cursor by pressing the 34 keys to
highlight the selected item.
➜ ON: At STOP mode, if nothing operation is
done within 5~6 minutes, screen saver will turn
on.
➜ OFF: Screen saver is disable.
4 Press OK to confirm.
5 Press the 1 key to return to the GENERAL
SETUP menu.
Quit the program playback
At the PROGRAM page,
1 Press the 1 234 keys to move the cursor to the
EXIT button.
2 Press the OK key to quit this menu.
Stop the program playback
0 During playing the programed tracks, press STOP
key. Then after you press PLAY key, the DVD
player will resume normal playback.
Repeat the program playback
0 During playing the programed tracks, press
REPEAT key, the programed tracks can be played
again.
VFD Dim
This function is used to adjust the brightness of
VFD on the front panel.
1 Press the 34 keys to highlight VFD DIM in the
GENERAL SETUP menu.
2 Enter its submenu by pressing the 2 key.
➜ pressing the 34 keys to select 100%/70%/
40% item.
3 Press OK to confirm.
4 Press the 1 key to return to the GENERAL
SETUP menu.
To Next Page
Loading...
