Philips Dynalite DDNG100BT User Manual

features
 Single Phase supply – 230 +/- 14% 50/60Hz 0.1A
 1 x RS485 Port – Dynet lighting control.
 1 x 10/100BaseT - Ethernet port
 Powerful Internal PLC - Custom scripts can be written
to provide process control based on conditional logic.
 DIN Rail Mounting - 12 Units wide.
Warning – This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.
Read Instructions – We recommend that you read this Instruction Manual prior
to commencement of installation.
Special Programming – This device will only operate in basic modes unless
programmed via a computer. If programming is required, contact your local
agent for details. Once the data cable is connected to the devices, the factory
default settings will allow any control panel to operate all channels in all
controllers.
Mounting Location – Install in a dry, well-ventilated location.
Data Cable – Use screened, stranded RS485 data cable with three twisted
pairs. Segregate from mains cables by 300mm. Connect devices in a ‘daisy
chain’. Do not cut or terminate live data cables.
Power Sources – This device should only be operated from the type of supply
specified on the front panel. This device must be earthed.
Megger Testing – Do not megger test any circuitry connected to the control
system, as damage to the electronics may result.
DDNG100BT
10/100BaseT Ethernet
Installation Manual
Warning
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS DEVICE TO RAIN OR MOISTURE.
DO NOT ENERGISE UNLESS THE FRONT COVER IS IN PLACE.
THIS DEVICE MUST BE EARTHED.
INSTALLATION, PROGRAMMING AND MAINTENANCE MUST BE
CARRIED OUT BY QUALIFIED PERSONNEL.
Electrical diagram

Philips Dynalite DDNG100BT Specifications

Power

supply voltage	230 +/- 14% 50/60Hz Single Phase
power consumption	450mA from the DyNet network at 12VDC

Ports & Interfaces

serial port 1	1 x 10/100BaseT Ethernet, 1 x RJ45 socket
serial port 2	1 x RS485 unterminated, 1 x RJ12 socket & 1 x 5 way terminal block
rs485 data formats	DyNet, DyNet II

Operating Environment

ambient temperature	0º to 50ºC
humidity	0% to 95% RH non condensing
compliance	CE, C-Tick

Weight and Dimensions

dimensions	H 93mm x W 211mm x D 75mm
weight	0.86kg
construction	Polycarbonate DIN Rail enclosure (12 unit)

Summary

Product Features

Single Phase Supply

Supports 230V +/- 14% 50/60Hz 0.1A single-phase power supply.

RS485 Port

Provides one RS485 port for Dynet lighting control.

Ethernet Port

Features one 10/100BaseT Ethernet port for network connectivity.

Powerful Internal PLC

Includes an internal PLC capable of custom scripts for conditional process control.

DIN Rail Mounting

Designed for DIN rail mounting and occupies 12 Units width.

Safety and Operational Warnings

General Safety Precautions

Isolate from mains, do not expose to moisture, ensure cover is in place, and earth the device for safety.

Product Interference

Class A product warning regarding potential radio interference in domestic environments.

Installation and Programming Guidance

Read manual before installation, use qualified personnel for programming and maintenance.

Data Cable and Power Source

Use specified RS485 cable, segregate from mains, use correct supply, and earth the device.

Megger Testing Caution

Avoid megger testing connected circuitry to prevent damage to electronics.

Electrical Diagram

Installation Steps

Connecting Data Cable

Recommended Cable Colour Coding

Recommended Cable Types

Product Specifications

Supply Details

Specifies single-phase 230V +/- 14% 50/60Hz supply.

Serial Port 1

Details the 1 x 10/100BaseT Ethernet port with an RJ45 socket.

Serial Port 2

Details the 1 x RS485 port with RJ12 socket and 5-way terminal block.

RS485 Data Formats

Specifies DyNet and DyNet II protocols for RS485 communication.

Internal Controls

Includes service switch, diagnostic LED, and a PLC with 64 tasks.

Operating Environment

Suitable for 0° to 50°C ambient temperature and 0% to 95% RH non-condensing.

Power Consumption

Consumes 450mA from the DyNet network at 12VDC.

Compliance

Complies with CE and C-Tick standards.

Construction

Features a polycarbonate DIN Rail enclosure, 12 units wide.

Dimensions

Measures H 93mm x W 211mm x D 75mm.

Weight

The device weighs 0.86kg.