Philips F Series User Manual

INSTALLATION INSTRUCTIONS
F Series Floodlight
© 2016 Philips Lighting Holding B.V. All rights reserved.
www.philips.com/luminaires
Part Number 443561002550 Rev. F
Page 1 of 7
IMPORTANT:
Read carefully before installing. All
work should be performed by a qualified
Electrician. These instructions may not
provide directions to cover every
variation and detail. To obtain
additional information, consult your
vendor or contact the factory directly for
assistance before attempting anything
with uncertainty. Improper installation
and/or utilization may void
manufacturer’s warranty.
This fixture must be grounded in
accordance with local codes and the
NATIONAL ELECTRIC CODE.
Failure to do so may result in serious
personal injury. HID luminaires should
be operated on grounded systems only.
Ungrounded power distribution systems
may carry high transient voltages which
can cause failure of any type electrical
equipment. Use of this equipment on
ungrounded systems will VOID THE
WARRANTY.
GENERAL:
Upon receipt, inspect for any freight
damage, which should be brought to the
attention of the delivering carrier. See
“Damage and Shortage Claims” for
proper steps in filing claims with the
carrier. Compare the catalog description
listed on the packing slip with the label
on the carton to assure you have received
the correct material.
This floodlight is designed for outdoor
lighting and should not be used in areas
with limited ventilation or within
enclosures having high ambient
temperatures. It is provided with an
integral mastfitter for mounting on a
vertical 2-3/8” OD tenon x 4-1/2” tall.
The flood light is UL listed for wet
locations (UL1598) and may be aimed
above horizontal.
WARNING: In no case mount this
floodlight to either a horizontal tenon
or inverted tenon.
IMPORTANT: The flood light optical
assembly are separately packaged.
After uncartoning, inspect for any
damage. If damage is noticed, see
“Damage and Shortage Claims Form”
(yellow) for proper steps in filing
claims with the carrier.
NOTE: Illustrations depict a 400 watt
fixture. Assembly and installation
procedures are the same for 1000 watt
and 1500 watt fixtures.

Philips F Series Specifications

General

Brand	Philips
Model	F Series
Category	Flood Light
Language	English

Summary

Fixture and Ballast Assembly

Lamping

Check lamp type and wattage before installing into socket.

Stabilux Lamp Socket

Grips lamp top for alignment and protection against breakage.

Ballast Assembly

Attach fixture mounting arms to the ballast enclosure.

Fixture Wiring

Electrical Connections

Make proper electrical connections according to NEC and local codes.

Grounding

Ensure proper grounding for personal safety.

Aiming

Vertical Aiming

Set fixture to proper aiming angle using markings or built-in device.

Horizontal Aiming

Adjust fixture for horizontal aiming using mounting ears.

Options

Vertical Floodlight Mounting

Mounting instructions for the vertical floodlight option.

Accessories

Mounting Brackets

FB1, PX-1, PM, SMB mounting bracket options.

Ballast Fusing

Accessory fusing kits for ballasts available for individual fusing.

Top Glare Shield

Install SK-100 or SK-40 top glare shield for fixture.

Auxiliary Lens

Install AL-10-F or AL-4-F polycarbonate auxiliary lens.

Shock Mounting Brackets

SMB-1000 or SMB-400 for mounting in severe vibration areas.

Wiring Components and Brackets

Wireguard

Attach WG-10 or WG-4 wireguard to fixture.

Mastfitter for Less Ballast

MF-1 mastfitter for remote mounting fixture head.

Trunion Base for Less Ballast

HV-1 trunion base for mounting to suitable surfaces.

Wall Mounting Bracket

WB-1 bracket for mounting floodlight to vertical surface.

Surface Wiring Box and Hanger

Surface Wiring Box

WB-5 wiring compartment for surface mounted conduit feed.

Hanger for Less Ballast Models

TH-1 hanger for mounting on standard lowering devices.