Philips FW-C100/21 - Tuner Operations; Tuning and Storing Radio Stations

2-7
SPR 00 0010
17
English
Tuner
Note: –For 'PLUG & PLAY' feature, please refer to page 11.
Tuning to radio stations
1
Press TUNER (BAND) to select TUNER mode. ➜ “TUNER” will be displayed. A few seconds later, the current radio frequency will be displayed.
2
Press TUNER (BAND) again to select the desired waveband : FM, MW or LW.
3
Press à or á for more than one second, then release. ➜ The display will show “SEARCH” until a radio station with sufficient signal strength is found.
¶ Repeat this procedure until the desired station is
reached.
¶ To tune to a weak station, briefly press à or
á repeatedly until the display shows the desired frequency and/or when the best reception has been obtained.
Storing Preset Stations You can store up to 40 radio stations in the memory. When a preset radio station is selected, the preset number appears next to the frequency on the display. Automatic programming
1
Press TUNER (BAND).
2
Press PROGRAM for more than one second. ➜ The PROG flag starts flashing and “AUTO” will be displayed. ➜ The system will search for every available station in the FM waveband first, MW and then search the LW waveband. ➜ All available stations will be stored automatically. The frequency and preset number will be displayed briefly. ➜ The system will stop searching when all the available radio stations are stored or when the memory for 40 preset radio stations is used. ➜ The system will remain tuned to the last stored preset radio station.
DIGITAL SOUND CONTROL
STANDBY
-
ON
PROGRAM CLOCK
•TIMER
MASTER
VOLUME
MINI HIFI SYSTEM
CD1 • 2 • 3
TAPE 1 • 2
TAPECD
AUX
PRESET
▲
▲
TUNING
▲
▲
▲
▲
STOP• CLEAR
SEARCH
PLAY• PAUSE PREV NEXT
VIDEO
O
P
T
I
M
A
L
J
A
Z
Z
R
O
C
K
T
E
C
H
N
O
DSC
DYNAMIC BASS BOOST
BAND
TUNER
DEMO STOP
2
21
3
TUNERTAPE 1/2CD
SLEEPAUXDIM
DSC DBB
MUTE
REPEAT
PAUSE
SHUFFLE
Å
CD DIRECT
VOLUME
á
à
ë
í
É
Ç
18
English
Tuner
Notes: –You can cancel the automatic programming by pressing PROGRAM or
Ç
(on the system only).
– If you want to reserve a section of preset numbers, for example preset numbers 1 to 9, select preset 10 before starting automatic programming, only the preset numbers 10 to 40 will be programmed. Manual programming
1
Press TUNER (BAND).
2
Press TUNER (BAND) again to select the desired waveband : FM, MW or LW.
3
Press PROGRAM for less than one second. ➜ The PROG flag starts flashing. ➜ The next available preset number will be displayed for selection.
4
Press à or á to tune to the desired frequency.
¶ If you wish to store the radio station to another
preset number, press 4 or 3 to select the desired preset number.
5
Press PROGRAM again. ➜ The PROG flag disappears and the radio station will be stored.
¶ Repeat steps 3 – 5 to store other preset radio
stations.
Notes: – When 40 radio stations are stored and you attempt to store another radio station, the display will show "FULL”. If you want to change an existing preset number, repeat steps 3 – 5. –You can cancel manual programming by pressing
Ç
(on the system only).
– During programming, if no button is pressed within 20 seconds, the system will exit programme mode automatically.
Tuning to Preset Radio Stations
¶ Press 4 or 3 to select the desired preset
number. ➜ The preset number, radio frequency, and waveband appear on the display.