23
English
3139 116 19761
TIMER SLEEP TIMER
5 Press CLOCK/TIMER again to store the
setting.
™ The clock starts.
• To exit without storing the setting, press
Ç on the system
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
Timer Setting
• The system can switch on to CD,
TUNER, or TAPE 2 mode automatically
at a preset time. It can serve as an
alarm to wake you up.
• Before setting the timer, make sure the
clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum level
until the volume level before the set
is switched to standby mode.
1 Press and hold CLOCK/TIMER for more
than
2 seconds
to select timer mode.
™ “ AM 12:00” or “00:00" or the
last timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The TIMER starts flashing.
™ The selected source is lit while other
available sources are flashing.
2 Press CD, TUNER or TAPE to select the
desired source.
• Before selecting CD or TAPE, make sure
a CD or tape is loaded in the CD tray or
tape deck 2.
3 Press␣ à or á on the system to set
the hour for the timer to start.
4 Press␣ í or ë on the system to set the
minute for the timer to start.
5 Press CLOCK/TIMER to store the start
time.
™ The timer is now set.
™ The TIMER remains on the display.
• At the preset time, the timer will be
activated.
™ The selected source will be played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the last
tuned frequency will be switched on.
– If the source selected is CD, playback
will begin with the first track of the
selected disc or program. If the CD trays
are empty, TUNER will be selected
instead.
– If the source selected is TAPE, and if the
preset time is reached during high
speed dubbing, the TUNER will be
selected instead.
– The timer will not activate if a recording
is in progress.
To switch off the TIMER
1 Press and hold CLOCK/TIMER for more
than
2 seconds
.
2 Press Ç on the system to cancel the
timer.
™ The timer is now switched off.
™ The display will show "OFF" and the
TIMER disappears.
To start the TIMER again
(for the same
preset time and source)
1 Press and hold CLOCK/TIMER for more
than
2 seconds
.
2 Press CLOCK/TIMER again to store the
start time.
™ The timer is now on.
™ The TIMER appears on the display.
Sleep Timer
(only on remote control)
This feature allows you to select a length
of time after which the system will switch
to the standby mode automatically.
1 Press SLEEP TIMER on the remote
control repeatedly to select a period of
time.
™ The selections are as follows (time in
minutes):
60 ™ 45 ™ 30 ™ 15 ™ OFF ™
60 …
™ "SLEEP XX" or "OFF" will be
displayed. "XX" is the time in
minutes.
2 When you reach the desired length of
time, stop pressing the SLEEP TIMER
button.
™ After this amount of time passes, the
system will switch to the standby
mode.
To switch off the Sleep Timer
• Press SLEEP TIMER repeatedly until
"OFF" is displayed, or press the
STANDBY ON button.
pg 01-26/P75/22-Eng 3/6/00, 12:41 PM23
To Next Page
Loading...
