INSTRUCTIONS FOR USE
3-6
PCS 104 588
Clock/Timer
PROGRAM
INTERACTIVE SOUND
STANDBY
ON
SHUFFLE
REPEAT
RDS
DBB
DSC
PRESETSTOP PLAY•PAUSE
iR
SENSOR
VOLUME
INCREDIBLE SURR.
CLOCK
TIMER
ON•OFF
CD
TIMER
SELECT
SOURCE
PROGRAM
TUNING
TUNING
RECORD
REV MODE
BAND
SIDE A/B
PREV NEXT
REV MODE
BAND
SIDE A/B
Setting the clock
There are two possible methods for setting the
clock: manually or automatically by using RDS.
Automatic clock setting (RDS versions
only)
1 Tune to a RDS station (see TUNER).
2 Press CLOCK for more than 2 seconds.
‹ SEARCH RDS TIME is displayed for a
maximum of 90 seconds; the time is then
displayed.
‹ NO RDS TIME is displayed if no time signal
has been received and you will have to set the
clock manually.
Manual clock setting
1 In standby, press CLOCK.
‹ The clock digits for the hours flash.
2 Tu rn VOLUME to set the hours: clockwise for
hours up; anti-clockwise for hours down.
3 Press CLOCK again.
‹ The clock digits for the minutes flash.
4 Tu rn VOLUME to set the minutes: clockwise for
minutes up; anti-clockwise for minutes down.
5 Press CLOCK to confirm the time.
Setting TIMER
¶ The system can be used as an alarm clock,
whereby the CD, TUNER or TAPE is switched on
at a set time. The clock time needs to be set first
before the timer can be used.
¶ You can also use it to record a favourite tuner
programme at a set period (REC TUN, see TAPE
RECORDER)
¶ During setting, if no button is pressed within 90
seconds, the system will exit timer setting mode
automatically.
1 In any mode, press TIMER ON•OFF for more
than 2 seconds.
2 Tu rn VOLUME clockwise to select sound
source.
‹ Display sequence shows CD, TUNER, TAPE or
REC TUNER.
3 Press TIMER ON•OFF to confirm your
desired mode.
‹ The selected source
or
TUNER
TUNER
is shown. Display sequence scrolls SET ON
TIME and TIMER flashes. The clock digits for the
hours flash.
4 Tu rn VOLUME to set the hours: clockwise for
hours up; anti-clockwise for hours down.
5 Press TIMER ON•OFF again.
‹ The clock digits for the minutes flash.
6 Tu rn VOLUME to set the minutes: clockwise for
minutes up; anti-clockwise for minutes down.
7 Press TIMER ON•OFF to confirm the time.
‹ The timer is now set and activated.
Activating and deactivating
TIMER
¶ In standby or during playback, press TIMER
ON•OFF on the system once (TIMER on the
remote control).
‹ Display shows TIMER if activated, and
disappears if deactivated.
Activating and deactivating
SLEEP
The sleep timer enables the system to switch off
by itself after a set period of time. The clock time
needs to be set first before the sleep timer can
be used.
¶ Press SLEEP on the remote
control once or more.
‹ Display shows SLEEP and
one of the sleep time options
in sequence: 60, 45, 30,15,
SLEEP OFF, 60... if you have
selected a time. Once SLEEP is activated, SLEEP
ON scrolls across the display at repeated
intervals.
Maintenance
Cleaning the Cabinet
¶ Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
¶ When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the centre
out.
¶ Do not use solvents such as
benzine, thinner, commercially
available cleaners, or antistatic
spray intended for analogue records.
Cleaning the disc lens
¶ After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
playback quality, clean the disc lens with Philips
CD Lens Cleaner or any commercially available
cleaner. Follow the instructions supplied with
cleaner.
Clock/Timer
Cleaning the Heads and the Tape Paths
¶ To ensure good recording and playback quality,
clean the heads A, the capstan(s) B, and
pressure roller(s) C after every 50 hours of
tape operation.
¶ Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
¶ You can also clean the heads by playing a
cleaning tape once.
To Next Page
Loading...
