CD Operation
5 To interrupt playback press PLAY•PAUSE 2;
(on the remote control 2;). Press
PLAY•PAUSE 2; (on the remote control 2;)
again to resume play.
The display freez es and the elapsed playing
time flashes when pla yback is inter rupted.
6 To stop disc playback, press STOP 9.
Note: CD play will also stop when;
– the CD door is opened.
– the disc has reached the end.
– you select another source: TAPE, TUNER or AUX.
– you select to standby.
– you press the tape deck PLAY
2
key.
Selecting a different track
Press PREV ¡1 or NEXT 2™ (on the remote
control ¡ or ™) once or repeatedly until the
desired tr ack number appears in the displa y.
If you have selected a track number shortly after
loading a disc or in the PA USE position, you will
need to press PLAY•PAUSE 2; (on the
remote control 2;) to start playback.
Finding a passage within a track
1 Press and hold down on PREV ¡1 or
NEXT 2™ (on the remote control à or á ).
The disc is played at high speed and low
volume .
2 When you recognise the passage you want,
release PREV ¡1 or NEXT 2™ (on the
remote control à or á ).
Normal playback continues.
Note:
– During a disc programme or if SHUFFLE/
REPEAT active, searching is only possible within the
same track.
IMPORTANT:
The lens of the CD player should never be
touched.
X
Playing a disc
This CD player plays Audio Discs including CD -
Recordables and CD-Rewritables.
CD-ROM, CD-I , CD V, VCD , DV D or computer
CDs, ho we ver, are not possible.
1 Select CD source .
2 Press OPEN•CLOSE on the
top
of the system to open the CD
compar tment.
OPEN is displayed when yo u
open the CD compartment.
3 Insert a disc with the printed side facing up and
press down on OPEN•CLOSE to close the
CD door .
READ is displayed as the CD player scans the
contents of a disc , and then the total number of
tracks and playing time are shown .
4 Press PLAY•PAUSE 2; (on the remote
control 2;) to start playback.
Current track number and elapsed playing
time of the track are displayed during disc
playback.
Basic Functions
IMPORTANT:
Before you operate the system, complete
the prepar
ation procedures.
Switching the system on
Press 2 STANDBY ON or SOURCE
SELECT .
The system will switch to the last selected
source .
Press CD, TUNER, TAP E or AUX on the
remote control .
The system will switch to the selected source.
To switch the system to standby mode
Press 2 STANDBY ON on the system or
remote control .
If in tape mode or recording mode
, press
STOP•OPEN first.
The vo lume level, interactive sound settings,
last selected source and tuner presets will be
retained in the player's memory.
Power-saving automatic standby
As a powe r-saving f eature , the system
automatically switches to standby 15 minutes
after a tape or CD has reached the end and no
control is operated.
Adjusting volume and sound
1
Tu rn the VOLUME control anti-clockwise to
decrease or clockwise to increase vo lume on the
system (or press VOL -/+ on the remote
control) .
Display shows the volume level VOL and a
number from 0-32.
2 Press DSC repeatedl y to select the desired
sound effect: CLASSIC (no indication)/
ROCK ( ) / JAZZ ( ) / POP ( ).
3 Press DBB to switch bass enhancement on or
off.
Display sho ws: if the DBB is activated.
4
Press INCREDIBLE SURR. (IS on the
remote control) to switch the surround sound
effect on or off.
Display sho ws: if activated.
Note:
– The effect of INCREDIBLE SURROUND may
vary with different types of music.
5 Press MUTE on the remote
control to interrupt sound
reproduction instantly.
Playback will continue
without sound and the display
shows MUTE.
To activate sound reproduction you can:
– press MUTE again;
– adjust the vo lume controls;
– change source .
To Next Page
Loading...
