Pilous ARG 250 plus S.A.F. User Manual

INSTRUCTION MANUAL
Pilous - pasove pily, spol. s r.o., Zelezna 9
tel.: 00 420 543 25 20 10, fax: 00 420 543 25 20 11, e-mail:pilous@pilous.cz
, 619 00 Brno, Czech Republic
ARG 250 S.A.F. • ARG 250 plus S.A.F. ARG 300 S.A.F.
ARG 300 plus S.A.F. ARG 330 S.A.F. ARG 330 plus S.A.F.
•
• •

Pilous ARG 250 plus S.A.F. Specifications

General

Brand	Pilous
Model	ARG 250 plus S.A.F.
Category	Lathe
Language	English

Summary

0. In general

0.1. Safety provisions

Machine design complies with rules, but user must observe safety instructions to prevent hazards.

0.2. Scope of use / use by determination

0.3. Requirements concerning operators

Machine operation by instructed and technically trained persons in safe work conditions.

0.4. Requirements concerning machines - safety equipments

3. Technical data

4. Installation

4.3. Connection to energy supplies

Instructions for safely connecting the machine to the electrical power supply.

5. Machine description

5.3. Band exchange, tensioning and adjustment

Procedure for replacing, tensioning, and adjusting the saw band for optimal cutting.

5.4. Guide heads - adjustment

How to adjust guide heads and hard-metal guides for band life and cut quality.

5.5.2. Material clamping

5.6. Control panel

Detailed layout and explanation of the machine's control panel buttons and displays.

Control Panel Overview and Indicators

Main Operation and Safety Controls

Explains buttons for MAIN SWITCH, TOTAL STOP, START, and HYDRAULIC UNIT.

Basic Functions and Arm Control

Details saw band control, arm position, and other basic functions.

5.7.1. Vice clamping pressure setting

Procedure for adjusting the vice clamping pressure using the regulation valve.

5.8. Arm uplift height setting

How to set the desired arm uplift height above the workpiece.

5.9. Regulation valve - saw band feed into cut

Explanation of the regulation valve for controlling saw band feed speed.

6. Saw bands

6.1. Saw bands design

6.2. Band tooth selection

Guidance on selecting the appropriate band tooth size for different materials.

6.3. Workpiece clamping

Methods for correct workpiece clamping to ensure cutting quality and band life.

6.4. Running-in the bands

Procedure for running-in new saw bands for optimal performance and life.

6.6. Recommended values for cutting

Table of recommended cutting speeds and feed rates for various materials.

7. Putting into operation

7.1. Safety Control

Checks to ensure the machine is in safe and perfect working condition.

7.2. First cut

8. Machine maintenance

8.1. Maintenance and control

Procedures for regular cleaning, lubrication, and checking of machine parts.

8.2. Repairs

9. Errors - reasons and elimination

Starting and Safety Errors

Addresses issues with band drive start and safety signal lamp activation.

Motor and Coolant Issues

Cutting Quality Errors

Saw Band Breakage and Feed Issues

10. Electrical scheme

10.1. Electrical scheme ARG 250 S.A.F., ARG 250 plus S.A.F., ARG 300 S.A.F., ARG 300 plus S.A.F.

Detailed electrical schematic for various machine models.

Scheme Description and Components

Component Part Numbers

11. Assembly

11.1. Guiding heads assembly

11.2. Idler wheel assembly

11.3. Table, turning table, pivot and vice assembly

11.3.1. Table, pivot and vice assembly ARG 250 S.A.F., ARG 300 S.A.F.

11.3.2. Table, turning table, pivot and vice assembly ARG 250 plus S.A.F., ARG 300 plus S.A.F.

11.4. Drive assembly

11.5. Coolant assembly

11.6. Hydraulic unit assembly

ATTACHMENT TO OPERATING INSTRUCTIONS FOR HYDRAULIC UNIT

Hydraulic Unit Assembly Principles

Hydraulic System Defect Survey

Safety at Work

Hydraulic Liquids Overview

Hydraulic Unit Parameters

EC Declaration of Conformity