Pioneer BDP-120 - User Manual

Other manuals for Pioneer BDP-120

Service Manual116 pages

System Firmware Update Instructions3 pages

Specifications2 pages

Questions and Answers

T
Theresa WolfeDec 1, 2025
What to do if my Pioneer BDP-120 cannot play a disc?
- S
  Shawn GreenDec 1, 2025
  If your Pioneer Blu-ray Player is not playing a disc, consider the following: * Take out the disc and clean it. * Ensure the disc is loaded correctly, aligned in the disc tray with the label-side up. * Verify the region code on the disc matches that of your player. * Allow any condensation in or near the player to dry. * Check that the disc is recorded in a compatible TV system (PAL or NTSC). * Note that the player cannot play back video that was not recorded normally. * Playback may be impossible due to the disc recording's state, a scratched, warped, or dirty disc, the state of the pick-up, or compatibility issues. * If the recorded time of a disc is unusually short, playback may not be possible. * BD-RE/-R discs recorded in a format other than BDMV/AVCHD cannot be pla...
J
Jasmine GonzalezAug 23, 2025
What to do if Pioneer BDP-120 Blu-ray Player screen freezes and buttons don't work?
- K
  Kyle WebsterAug 25, 2025
  If you're experiencing a frozen screen and the operation buttons aren't working on your Pioneer Blu-ray Player, try the following: * Press the STOP button, then restart playback. * Turn the power off and then on again. * If the power doesn't turn off, perform a reset. * Check the condition of the disc for damage or dirt.
C
Crystal RomanAug 25, 2025
Why is KURO LINK not working on my Pioneer Blu-ray Player?
- R
  Richard ReevesAug 26, 2025
  If the KURO LINK function on your Pioneer Blu-ray Player isn't working, ensure the HDMI cable is properly connected. Use High-Speed HDMI™ cables for the KURO LINK function. Set “Settings” – “KURO LINK” on the player to “Yes.” Note that the KURO LINK function does not work with devices of other brands, even if connected via HDMI. Also, ensure KURO LINK is enabled on the connected device and that the player’s picture is properly output to the Flat Screen TV. The KURO LINK function may not work if three or more players, including this player, are connected.
J
jessica57Aug 27, 2025
Why does my Pioneer BDP-120 turn off automatically?
- E
  Elizabeth SmithAug 27, 2025
  Your Pioneer Blu-ray Player might be turning off automatically because either 'Auto Power Off' is set to 'Yes', in which case the power will turn off after 10 minutes of inactivity, or 'KURO LINK' is set to 'Yes', and the player's power turns off when the connected TV is turned off.
S
Steven FosterAug 27, 2025
Why does my Pioneer BDP-120 turn on automatically?
- A
  Angela BryantAug 27, 2025
  If your Pioneer Blu-ray Player turns on automatically, it might be because 'KURO LINK' is set to 'Yes'. This setting can cause the player to power on when the connected TV is operated.
G
Gary ArnoldSep 15, 2025
Is it normal for my Pioneer Blu-ray Player to heat up?
- R
  Rhonda GutierrezSep 16, 2025
  If your Pioneer Blu-ray Player heats up during use, the console cabinet may heat up depending on the usage environment. This is normal.
J
Justin RobinsonSep 13, 2025
Why is the playback screen disturbed when using my Pioneer BDP-120 Blu-ray Player with a VCR?
- M
  mariahicksSep 13, 2025
  If the playback screen is disturbed when DVD video is recorded to a VCR, or played back through a VCR using your Pioneer Blu-ray Player, it may be because some discs contain a copy prohibiting signal. This player complies with analog copy protection.
J
James KochSep 14, 2025
Why does my Pioneer Blu-ray Player automatically switch inputs on connected devices?
- F
  fsantanaSep 14, 2025
  If the input of connected TV, AV system, and HD AV Converter switches automatically when using your Pioneer Blu-ray Player, it is because “Settings” – “KURO LINK” is set to “Yes” on the player. With this setting, the input on the connected devices may switch automatically.
J
Joshua JonesSep 6, 2025
Why doesn't the KURO LINK indicator light up on my Pioneer BDP-120 Blu-ray Player?
- L
  Lauren GlassSep 6, 2025
  If the KURO LINK indicator on your Pioneer Blu-ray Player does not light up, connect to a KURO LINK-compatible Pioneer Flat Screen TV using an HDMI cable. Set KURO LINK to On on the Flat Screen TV and set “Settings” – “KURO LINK” on the player to “Yes.” Also, check that the player’s picture is being output to the Flat Screen TV.
J
Jessica SilvaSep 3, 2025
How to troubleshoot no picture on Pioneer Blu-ray Player?
- B
  Beverly WoodSep 3, 2025
  If you're not getting a picture from your Pioneer Blu-ray Player, make sure the cables are connected correctly. Also, ensure that the connected TV or AV receiver is set to the correct input. Try taking out the disc and cleaning it. Verify that the region code on the disc matches that of your player. Check the settings for the HDMI and component video outputs to ensure they are correctly configured.