SPEAKER
SYSTEM
OPERATING
GUIDE
HPM-ltCICI
()rrloNEER'
IMPORTANT
NOTlCE:
The serial
number
for
this equipment is located on
the
reaf,
Please
write this
serial
number on
your
enclosed
warran-
ty card and keep in a secure area. This is for
your
secu ntv.
BEFORE
USE
.
Please
read this operating
guide
through
before using
your
speaker
system so
you
will know how to make
the
most
of its
performance.
After
you
have finished
reading
the operating
guide.
store the leaflet in
a safe
place.
You
will
then
know
where it is. should
you
wish
to refer
to it if
something
is
unclear while the
speaker
system is being used.
o
The nominal
impedance of this speaker
system is
6.3
ohms.
Connect
the
speakers to a stereo
amplifier
with
a
load impedance ranging from 4
to 16
ohms
(a
model
with
"4
-
16A" displayed
on
the
speaker output
terminals).
r The maximum
input
power
of these
speakers is 250
wattr.
Tire speakers may'bscfatfaged or
ynalrge
sounds
may
be heard
through them if signals with a
strength
exceeding
the maximum input
power
are applied.
r
Remember to handle the
speaker system carefully
since
it
is
quite
heavy.
INSTALLATION
o The normal listening
position
is at the apex of an
imaginary
equilateral
triangle with the speaker system
forming
the base line. Alternatively,
you
can sit
and
listen
lust
beyond
the apex.
Left speaker
system
Right
speaker
system
Listening
position
r
The
sound
quality
may change
depending
on
the
objects
surrounding
the speaker
system,
the installation loca-
tions,
and the
listening room
itself.
The bass, for in-
stance,
will sound
different
when the speaker
system is
placed
up against a wall
and
when there is
a crearance
between
the speaker
system
and the wall.
See
what the
sound is like
in a number
of
positions
and choose the
location
which offers
a sound
quality
to
your
liking.
I NSTALLATION PR
ECAUTIONS
a Do not
install this
speaker system near
a
stove
or
other heating
appliance, and
do not
put
it in a
place
exposed
to
the sun. Locations
like
these may cause the
cabinet
to change color
and the
speaker system
to break
oown.
r Remember
that this speaker
system
is
quite
heavy.
so it
is dangerous to
install it in a
high
place
like
on a wall or
pillar
or in
other unstable locations.
CONNECTIONS
1
. Set
the
amplif
ier's
power
switch to
OFF.
2. Connect input terminal
(+)
of
the
speaker system to
---o-utput
ieiminal
(+)
oi amplifier, bnilinpdi-ierminal
(-)
to output terminal
(-).
@
Speaker
cords
O e
o
Speaker's
input
terminals
Depress
the
input
terminal knob,
insert
the tip of
the cord into
the
hole
and then release
the knob
so
that
it springs back into
position.
NOTES:
o Make
sure that
the
speaker cords are connected
to the terminals securely.
lnsecure
connections may
cause not only
sound
to be interrupted
and
noise
to
be
generated
but also the cords to
be shorted
and the
amplifier to
break down-
o
When
listening to
a
stereo
performance
with
the
speaker system connected to a
stereo
amplifier,
you
will
find
that the bass is insufficient.
the sound
is
not
spread
out and
there
is
no
stereo
effect if the
cords
of
one
of the
speaker system have been
plugged
into
the
wrong
polarity
terminals.
@
Rustr\
@
Insen
Caution:
Bear in
mind
that the cone
of these speakers may
be deformed
by heat if
the speakers are installed
in
direct sunlight or in the
vicinity
of a heater for
a
prolonged
period
of time.
To Next Page
Need help?
General
