EasyManua.ls Logo

Pioneer VSX-D6025 - User Manual

Pioneer VSX-D6025
44 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating
Instructions
WD
PHONEER
srecreee
arones
necoves
WSX-D7025
DEMO
MODE
Thank
you
for
buying
this
Pioneer
product.
Please
read
through
these
operating
instructions
so
you
will
know
how
to
operate
your
model
properly.
After
you
have
finished
reading
the
instructions,
put
them
away
in
a
safe
place
for
future
reference.
In
some
countries
or
regions,
the
shape
of
the
power
plug
and
power
outlet
may
sometimes
differ
from
that
shown
in
the
explanatory
drawings.
However,
the
method
of
connecting
and
operating
the
unit
is
the
same.
WARNING:
To
PREVENT
FIRE
OR
SHOCK
HAZARD,
DO
NOT
EXPOSE
THIS
APPLIANCE
TO
RAIN
OR
MOISTURE.
IMPORTANT
NOTICE
[For
U.S.
and
Canadian
models]
The
serial
number
for
this
equipment
is
located
on
the
rear
panel.
Piease
write
this
serial
number
on
your
enclosed
warranty
card
and
keep
it
in
a
secure
area.
This
is
for
your
security.
Note
to
CATV
system
installer
This
reminder
is
provided
to
call
the
CATV
systern
installer’s
attention
to
Article
820-40
of
the
NEC
that
provides
guidelines
for
proper
grounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building,
as
close
to
the
point
of
cable
entry
as
practical.
*
The
demonstration
mode
is
activated
by
turning
on
the
power:
switch
while
holding
down
the
RETURN
button
(from
power
standby
condition).
The
demonstration
will
appear
on
the
display.
©
Press
the
POWER
switch
to
cancel
the
demonstration.
©
Activating
the
demonstration
mode
causes
memory
contents
to
return
to
their
original
default
condition
except
tuner.
AUDIO/VIDEO
STEREO
RECEIVER
V9SX-D6025
VSX-D7025
*
Illustration
shows
model
VSX-D702S.
[For
Canadian
model]
CAUTION:
To
PREVENT
ELECTRIC
SHOCK
DO
NOT
USE
THIS
(POLARIZED)
PLUG
WITH
AN
EXTENSION
CORD,
RECEPTACLE
OR
OTHER
OUTLET
UNLESS
THE
BLADES
CAN
BE
FULLY
INSERTED
TO
PREVENT
BLADE
EXPOSURE.
ATTENTION:
pour
PREVENIR
LES
CHOCS
ELECTRIQUES
NE
PAS
UTILISER
CETTE
FICHE
POLARISEE
AVEC
UN
PROLONGATEUR
UNE
PRISE
DE
COURANT
OU
UNE
AUTRE
SORTIE
DE
COURANT,
SAUF
SI
LES
LAMES
PEUVENT
ETRE
INSEREES
A
FOND SANS
EN
LAISSER
AUCUNE
PARTIE
A
DECOUVERT.
RETURN
function
This
function
returns
the
unit
to
a
set
of
initial
settings
and
ready
to
broadcast
tuner.
This
is
helpful
during
troubleshooting
or
when
no
sound
is
output.
For
details,
refer
to
page
20.
@
PIONEER’
The
Art
of
Entertainment

Table of Contents

Question and Answer IconNeed help?

Do you have a question about the Pioneer VSX-D6025 and is the answer not in the manual?

Overview

  1. Function Description
  2. Important Technical Specifications
    1. Amplifier Section
    2. FM Tuner Section
    3. AM Tuner Section
    4. Video Section
    5. Miscellaneous
  3. Usage Features
  4. Maintenance Features

This document describes the Pioneer VSX-D602S/VSX-D702S Audio/Video Stereo Receiver, a central component for audio-video entertainment systems.

Function Description

The VSX-D702S/VSX-D602S combines the functions of a receiver, wireless remote control, audio-visual selector, and surround processor. It is designed to play a central role in your enjoyment of audio-video media.

Key functions include:

  • DOLBY PRO LOGIC SURROUND performed by a Digital Signal Processor (DSP).
  • DSP provides Sound Field Control (SFC) simulated surround settings.
  • VIDEO SIGNAL SELECTOR (Simulcast function): Allows free combination of various audio-visual sources during playback and over-dubbing, enabling you to produce your own original video product.
  • TWO-WAY VCR COPYING AND MONITORING:
    • VCR 1 ↔ VCR 2: Copying of video cassette tapes can be performed in either direction.
    • LD, TV, VIDEO → VCR 1, VCR 2: Allows simultaneous production of two copies from video disc or compact disc with video.
  • ACOUSTIC MEMORY FUNCTION: Five types (A-E) of tone control settings can be preset. Settings for loudness and flat tone response functions can also be quickly selected.
  • CUSTOM MEMORY FUNCTION: Stations can be preset according to the genre of the material broadcast, and Memory Scan of a particular genre can be carried out.
  • 90/60/30-MINUTE SLEEP TIMER FUNCTION.
  • MULTI-ROOM REMOTE JACK: The optional MR-100 Multi-room remote control unit can be connected to the Multi-room remote IN jack.
  • AV PROGRAMMABLE REMOTE CONTROL UNIT: With the attached programmable remote control unit, you can operate any Pioneer audio or video component bearing the Pioneer mark. The LEARN function allows memorizing remote commands of components not bearing the Pioneer mark, providing remote control over a component's functions. The MULTI-COMMAND feature allows memorizing up to seven commands in order, transmitting them with a single button push.
  • DEMO MODE: Activated by turning on the power switch while holding down the RETURN button (from power standby condition). The demonstration appears on the display and can be canceled by pressing the POWER switch. Activating demo mode causes memory contents to return to their original default condition, except for the tuner.
  • RETURN function: Returns the unit to a set of initial settings and ready to broadcast tuner. This is helpful for troubleshooting or when no sound is output.

Important Technical Specifications

Amplifier Section

  • Continuous average power output: 110 watts per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.05% total harmonic distortion (front).
  • Continuous power output (Front and center driven): 70 W + 70 W (1 kHz, 0.8%, 8 Ω).
  • Center: 70 W (1 kHz, 0.8%, 8 Ω).
  • Dynamic Power (2 Ω/4 Ω): 240 W/220 W.
  • Input (Sensitivity/Impedance):
    • PHONO MM: 2.5 mV/47 kΩ.
    • CD, TAPE 1/DAT, TAPE 2, LD, VCR 1, VCR 2: 150 mV/47 kΩ.
  • Phono Overload Level (T.H.D. 0.1%, 1 kHz) PHONO MM: 120 mV.
  • Frequency Response:
    • PHONO MM: 20 Hz to 20,000 Hz ±0.3 dB.
    • CD, TAPE 1/DAT, TAPE 2, LD, VCR 1, VCR 2: 5 Hz to 100,000 Hz ±3 dB.
  • Output (Level/Impedance):
    • TAPE 1/DAT REC, TAPE 2 REC: 150 mV/2.2 kΩ.
    • VCR 1 OUT, VCR 2 OUT: 150 mV/2.2 kΩ.
  • Tone Control:
    • BASS: ±8 dB (100 Hz).
    • TREBLE: ±8 dB (10 kHz).
  • Muting: -∞ dB.
  • Loudness Contour: 6 dB (100 Hz), 3 dB (10 kHz).
  • Signal-to-Noise Ratio (IHF, short circuited, A network):
    • PHONO MM: 76 dB.
    • CD, TAPE 1/DAT, TAPE 2, LD, VCR 1, VCR 2: 97 dB.
  • Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]:
    • PHONO MM: 77 dB.
    • CD, TAPE 1/DAT, TAPE 2, LD, VCR 1, VCR 2: 80 dB.

FM Tuner Section

  • Frequency Range: 87.5 MHz to 108 MHz.
  • Usable Sensitivity: Mono: 10.8 dBf, IHF (0.95 µV/75 Ω).
  • 50 dB Quieting Sensitivity: Mono: 15.3 dBf, (1.6 µV/75 Ω); Stereo: 37.0 dBf, (19.5 µV/75 Ω).
  • Signal-to-Noise Ratio: Mono: 80 dB (at 65 dBf); Stereo: 76 dB (at 85 dBf).
  • Distortion: Mono: 0.2% (1 kHz); Stereo: 0.3% (1 kHz).
  • Capture Ratio: 1 dB.
  • Alternate Channel Selectivity: 65 dB (400 kHz).
  • Stereo Separation: 45 dB (1 kHz).
  • Frequency Response: 30 Hz to 15 kHz (±3 dB).
  • Antenna Input: 300 Ω balanced, 75 Ω unbalanced.

AM Tuner Section

  • Frequency range:
    • With 9 kHz step: 531 kHz – 1,602 kHz.
    • With 10 kHz step: 530 kHz – 1,700 kHz.
  • Sensitivity (IHF, Loop antenna): 300 µV/m.
  • Selectivity: 25 dB.
  • Signal-to-Noise Ratio: 50 dB.
  • Antenna: Loop antenna.

Video Section

  • Input (Sensitivity/Impedance): VCR 1, VCR 2, LD: 1 Vp-p/75 Ω.
  • Output (Level/Impedance): VCR 1, VCR 2, MONITOR: 1 Vp-p/75 Ω.
  • Frequency Response: VCR 1, VCR 2, LD – MONITOR: 5 Hz – 7 MHz ±3 dB.
  • Signal to Noise Ratio: 55 dB.
  • Cross Talk: 55 dB.

Miscellaneous

  • Power requirements:
    • U.S. and Canadian models: AC 120 V, 60 Hz.
    • Multi-voltage model: AC 110 V/120 – 127 V/220 V/240 V (Switchable), 50/60 Hz.
  • Power consumption:
    • U.S. and Canadian models: 260 W, 340 VA.
    • Multi-voltage model: 660 W.
  • AC Outlets:
    • U.S. and Canadian models: SWITCHED x 2 (TOTAL 100 W (0.8 A) MAX), UNSWITCHED x 1 (100 W (0.8 A) MAX).
    • Multi-voltage model: SWITCHED x 2 (TOTAL 100 W MAX), UNSWITCHED x 1 (100 W MAX).
  • Dimensions: 420 (W) x 162 (H) x 406 (D) mm (16-9/16 (W) x 6-3/8 (H) x 16 (D) in).
  • Weight (without package): 10.2 kg (22 lb 8 oz).

Usage Features

  • Large, Motor-Driven Volume Knob: Contributes to operational convenience and positive response. Can be operated via remote control, with the knob turning by itself to track the current setting.
  • Speaker Connections: Supports front, center, and rear speakers. The VSX-D702S has two sets of center speaker terminals for dual center speaker use. Impedance requirements: 8Ω to 16Ω for front and rear, 8Ω to 16Ω for center (I ONLY operation), 4Ω to 16Ω for center (I + II operation).
  • S-VIDEO Connectors (VSX-D702S only): For VCR 1, LD, and TV monitor with S-VIDEO connectors. S-VIDEO connectors are for video only; audio connections must be made separately.
  • Tuner Functions:
    • Direct Access Tuning: Input desired station frequency directly using number buttons.
    • Auto Tuning: Scans for stations in ascending or descending frequency order.
    • Manual Tuning: Adjusts frequency step-by-step.
    • Preset Tuning: Memorizes up to 30 AM and FM stations, including MPX AUTO/MONO mode.
    • Custom Memory Selection: Memorize stations under five genre names (ROCK, POP, JAZZ, NEWS, OTHER).
    • HITS (Hyper Intelligent Tuning System): Searches for stations within 1 MHz ranges (FM) or 100 kHz ranges (AM) during direct access tuning or frequency display.
    • FM Auto Stereo/Monaural Reception: Automatically switches between stereo and monaural based on signal strength.
  • Acoustic Memory: Allows presetting and recalling up to five sound quality settings (FLAT, LOUDNESS, A-E).
  • Video Signal Selector: Allows listening to playback sound while changing the video image, enabling playback and recording of different video images from the playback sound source.
  • Auto Source Control: Memorizes receiver settings and recalls them with a single button. Can automatically switch on power and start play of Pioneer components connected to the CONTROL OUT jack.
  • Remote Control Operation:
    • Programmable: Can learn commands from other infrared remote control units.
    • Preset Modes: Includes preset signals for VCR 1, VCR 2, and TV functions.
    • Multi-Edit Mode: Program up to seven commands into the MULTI COMMAND button for sequential transmission.
    • Initialization: Allows returning individual CONTROL MODES or the entire memory to initial settings.

Maintenance Features

  • Power-Cord Caution: Handle the power cord by the plug, avoid pulling the cord, touching with wet hands, placing objects on it, or pinching it. Check for damage periodically.
  • Cleaning: Clean the appliance only with a polishing cloth or a soft dry cloth. Avoid furniture wax, benzine, insecticides, or other volatile liquids to prevent cabinet corrosion.
  • Battery Replacement (Remote Control): Replace batteries when CONTROL MODE buttons do not light properly. Use size "AA" (IEC LR6/AM-3) alkaline batteries. Do not mix new and used batteries or different types.
  • Troubleshooting Guide: The manual includes a comprehensive troubleshooting section to address common issues related to power, control, sound, picture, noise, and recording, with suggested remedies.
  • External Surfaces Maintenance: Wipe dust and dirt with a polishing cloth or dry cloth. For very dirty surfaces, use a soft cloth dipped in a diluted neutral cleanser and wrung out well, then wipe with a dry cloth. Avoid thinners, benzene, insecticide sprays, and other chemicals.

Pioneer VSX-D6025 Specifications

General IconGeneral
BrandPioneer
ModelVSX-D6025
CategoryStereo Receiver
LanguageEnglish

Related product manuals