Pioneer XR-P260F User Manual

|
_
TURNING
ON
THE
POWER
I
TUNING
INTO
STATIONS
Operations indicated by the [/
remote
control
unit.
=
I] mark are performed with the
Read
“CONNECTIONS”
again
and
ensure
that
speakers,
antenna,
ete.,
are
connected
properly.
Press the POWER switch.
STANDBY
F
°
=
POWER
POWER
POWER Al (o_)
mime
SO
RL
RK
To switch the power OFF:
Press the POWER switch again.
The
clock
display
reappears
and
the
STANDBY
indicator
lights.
|
Turning
power
ON
without
using
the
POWER
switch
Performing
any
of
the
following
operations
while
the
system
power
is
off
(STANDBY)
turns
the
power
ON,
lf a CD has been loaded, it
starts to play.
oe The tuner (radio) input is
po fal FWAM | ay | Selected.
As
lf a cassette tape has been
loaded, it starts to play.
If the connected component
is operating, it starts to play.
The function which has been
selected before the last time
the power was switched off
is selected and the
corresponding operation
starts,
Fete
'
To
change
the
frequency
step
'
:
The
frequency
step
(AM:
9
kHz/10
kHz,
FM:
50
kHz/100
kHz)
is
;
1
Preset
depending
on
the
area.
If
you
need
to
change
the
step,
,
5
follow
the
next
procedure.
1
i
1.
Turn
off
the
power.
:
12.
While
pressing
the
FREQ/STATION
button,
turn
on
the
'
1
power.
'
'
'
i
Repeat
1-2
to
reset
the
frequency
step.
#Be
sure
to
connect
the
antennas.
Do
not
place
the
AM
antenna
on
a
metallic
case
including
the
receiver
cabinet
or
near
a
CD
player,
LD
player,
DAT
recorder,
personal
computer
or
TV
set.
Any
of
these
installations
will
cause
noise
in
reception.
1,
Press
the
tuner
(FM/AM)
function
button.
Select
the
FM
or
AM
broadcasting
band.
Each
time
you
press
this
button,
FM
and
AM
changes
alternately.
Aaa aceericecal iceman
2.
Tune
in
the
desired
station
by
pressing
the
or
[23
button.
Manual tuning
Tap
the
<3]
or
[E>
button
in
quick
repetitions.
@ Auto tuning
Press
the
or
button
for
a
second
or
two
and
remove
your
finger
from
it
when
the
frequency
starts
to
change.
~The
frequency
changes
automatically.
When
a
station
is
received,
the
frequency
stops
changing
and
“TUNED”
appears
on
the
display.
@ High-speed manual tuning
Press
and
hold
the
<3]
or
[>
button.
—The
frequency
changes
Continuously
and
stops
when
your
finger
is
removed
from
the
button.
MONO
button
(Remote
control
unit
only)
During
FM
reception:
Switches
between
stereo
and
monaural
modes
when
listening
to
a
stereo
broadcast.
If
there
is
a
lot
of
noise
in
the
stereo
position,
switch
to
MONO,
and
the
noise
will
be
suppressed,
Beat cut function
If
noise
occurs
during
recording
an
AM
broadcast,
perform
the
following
procedures
to
reduce
the
noise.
1.
Press
the
POWER
switch
on
this
unit
so
that
the
STANDBY
indicator
lights
up.
2.
Turn
on
the
power
while
pressing
the
MEMORY
button.
{The
BEAT
CUT
indicator
lights.)
eTo
cancel
the
BEAT
CUT
function,
repeat
steps
1
and
2.
BEAT CUT indicator lights. "1
<ARB7056>

Pioneer XR-P260F Specifications

General

Brand	Pioneer
Model	XR-P260F
Category	Cassette Player
Language	English