Pitney Bowes da95f Service Manual

Name: Pitney Bowes da95f
Brand: Pitney Bowes
Rating: 4 (1 reviews)

199 pages

To Next Page

Service Manual

DA80F and DA95F

AddressRight

™

Fixed Head Printers

DA80F (WF81)

DA95F (WF96)

Default Chapter1
- Service Manual1
- Table of Contents3
Chapter 1 - Introduction7
- Purpose of this Manual7
- Book Organization8
- 1.4 Safety8
Chapter 2 - Specifi Cations11
- Product Description11
- System Requirements11
- Physical Equipment Specifications11
- Print Specifications13
- Material Specifications17
Chapter 3 - Theory21
- Changes from Earlier Models21
- Printer Architecture22
- Operating Sequence25
Chapter 4 - Troubleshooting/Diagnostics27
- Block Diagrams28
- Main Controller Board Diagnostics30
- Error Codes35
- Print Samples for Troubleshooting38
- Troubleshooting39
- Feeding Issues40
- Printing Issues45
- Display Issues49
- Miscellaneous Issues49
Chapter 5 - Removal & Replacement51
- List of Procedures51
- Rear Cover and Keyboard/Lcd Display Board53
- Main Processor Board54
- Encoder Assembly57
- Paper Top Sensor Assembly (Emitter)59
- Paper Bottom Sensor Assembly (Receiver)59
- Feeder Sensor Assembly (Emitter and Receiver)60
- Front Bottom Cover Assembly61
- Transport Timing Belt62
- Feed Motor Timing Belt63
- Feed Roller Pulley and Feed Roller Assembly64
- Roller Assembly65
- Transport Motor Assembly68
- Motor Assembly69
- H-Block Assembly (Media Separators)70
- Print Head Cables and Print Head Boards71
- Entry Idler Roller Arm78
- A Feed Deck80
- B Front Plate Assembly82
- Transport (Metal Grit) Roller84
- Exit (Rubber) Roller86
- Power Supply87
- Print Head Access Door88
- Rear Cover/Side Guides89
- Lower Sensor Receiver Assembly91
- H Block" Roller (Media Separator)93
- Feed Belts and Rollers94
- Motor/Drive Assembly97
  - Printer Top Cover98
  - Front Cover and Keyboard/Lcd Display Board99
- Rear Cover and Processor Board101
  - Rear Cover and Processor Board102
- Paper Sensor and Sensor Bar104
- Entry Roller Support Assembly105
- Intermediate Idler Rollers Assembly106
- Idler Roller Support ("Module A") Assembly107
- Idler Roller Support ("Module B") Assembly107
- Idler Roller Support ("Module B") Assembly108
- Print Head Cables and Print Head Boards109
- Belt Drive Assembly117
- Media Belts119
- Encoder Assembly121
- Drive Belt/Motor Assembly124
- Power Supply125
Chapter 6 - Adjustments127
- List of Adjustments127
Adjustments for All Models127
- LCD Display127
- Feeder Sensor Test and Calibration128
DA80F (WF81) Adjustments129
- Leveling the Print Head Assembly to Deck (Belts)129
DA95F (WF96) Adjustments131
- Leveling the Print Head Assembly to Deck131
- Adjustable Thickness Knob and Eccentric Sprockets132
Chapter 7 - Maintenance Procedures135
- General Maintenance135
- Specific Maintenance136
Appendix A - Printer Control Panel Menus and Utilities137
- Control Panel Menus for the Printer137
- For the Printer138
- A.2 LCD Control Panel Menu139
- LCD Main Menu140
- LCD Setup Menu146
  - Use Conveyor146
TIP: after Changing a147
- Again for the New Set147
- Setup Menu, You Need147
- The RJ-11 Connec147
- Tings to be Recognized147
TIP: for a Pin-Out of147
- To Power down the Printer and Power It up147
  - Setup Menu149
  - Enable, Disable152
- LCD Service Menu159
- Setting Factory Defaults (from LCD Menu163
- Conveyor Type164
  - Activate Polarity Rising Edge164
  - Conveyor on164
Lines Per Address164
- Line Termination164
- Port Number164
- Printer Control Panel Menus and Utilities • Appendix A164
- Tcp/Ip164
- Use Conveyor164
- Updating Firmware166
  - Subnet Mask167
Appendix B - Printer Communications171
- B.1 Communication Scenarios171
- Troubleshooting Tables174
  - Clear Memory174
- Testing Printer Communications Within a Network176
Appendix C - Schematics179
- Main Processor Board for both Printers179
- DA80F (WF81) Printer Block Diagram179
- DA95F (WF96) Printer Block Diagram179
Appendix D - Print Head Alignment183
- Reason for this Appendix183
- Print Head Alignment Procedure184
Appendix E - Printing Standards189
- USPS® Delivery Point Barcode (DPBC190
- USPS® PLANET Code Barcode191
Index198

Other manuals for Pitney Bowes da95f

Operator's Guide92 pages

Frequently Asked Questions37 pages

Questions and Answers:

Need help?

Do you have a question about the Pitney Bowes da95f and is the answer not in the manual?

Pitney Bowes da95f Specifications

General

Print Resolution	203 dpi
Connectivity	USB, Serial, Ethernet
Category	Label Printer
Print Technology	Direct Thermal
Memory	4 MB Flash
Supported Barcode Types	Code 39, Code 128, UPC-A, UPC-E, EAN-8, EAN-13, Interleaved 2 of 5, Postnet, PDF417
Supported Media Types	Labels, Tags, Tickets
Media Thickness	0.0025" to 0.008 inches
Operating Temperature	104°F
Storage Temperature	-4°F to 140°F (-20°C to 60°C)