Planet POE-E101 User Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Introduction
1.1 Packet Contents
Thank you for purchasing PLANET POE-E101 IEEE
802.3af Power over Ethernet Extender, your Power
over Ethernet Extender package shall contains following
contents:
Check the contents of your package for following parts:
Power over Ethernet Extender x 1
User's Manual x 1
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
carton including the original packing material, and use them
against to repack the product in case there is a need to
return it to us for repair.
1.3 TechnicalSpecication
Model POE-E101
Interfaces
LAN IN
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” in Auto MDI/
MDI-X, Auto-negotiation RJ-45 connector
LAN OUT
1 x 10/100Base-TX Ethernet with IEEE
802.3af PoE “Data + DC” out Auto
MDI/MDI-X, Auto-negotiation RJ-45
connector
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet
PoE Power
Supply Type
Mid-Span / Type B
PoE Power
Output
48V DC, 270mA, Max. 13 Watts
Power Pin
Assignment
4/5(+), 7/8(-)
Hardware Specication
Data Rate 10/100Mbps
Switch
Architecture
Store-and-Forward
Switch
Throughput
148810pps@64Bytes
Latency 7.840µs
2.2 Ports connection
IN Port
Connect the PoE IN port from following
802.3af PSE device through a CAT-5e/6 UTP
cable:
• PoE injector
• PoE Injector Hub
• PoE Ethernet Switch
• Previous POE-E101
OUT Port
Connect the PoE OUT port to following
802.3af PD device through a CAT-5e/6 UTP
cable:
• PoE IP Camera
• PoE VoIP Phone
• PoE Wireless AP
• PoE Splitter
• Next POE-E101
2.3 LEDdenition:
LED Color Function
PoE IN
Green
Lights to indicate the port is
providing 48VDC in-line power.
LNK/
ACT
Green
Lights to indicate the port is link up.
Blink: indicate that the extender is
actively sending or receiving data
over IN port.
PoE OUT
Green
Lights to indicate the port is
providing 48VDC in-line power.
Standard
Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 10/100Base-TX Fast
Ethernet
IEEE 802.3af Power over Ethernet PSE /
Mid-Span
IEEE 802.3af Power over Ethernet PD /
Mid-Span
IEEE 802.3x Flow Control
Environment
Operating
Temperature: -10 ~ 60 Degree C
Relative Humidity: 0 ~ 95%
(non-condensing)
Storage
Temperature: -40 ~ 85 Degree C
Relative Humidity: 5 ~ 95%
(non-condensing)
1.2 Key Features
● ComplieswithIEEE 802.3af Power over Ethernet
● Extends the range of PoE an additional 100 meters
(328ft.)
● Forwards both Ethernet
data and PoE power to remote
device
● Auto-detect and protect of PoE equipment from being
damaged by incorrect installation
● Multipleunits,daisy-chaininstallationsupport
● Noexternalpowercableinstallationrequired
● Compactsize,Wall-mountabledesign
● Plug-and-Play installation
Maximum
Frame Size
1552Bytes
Flow Control
Back pressure for Half-Duplex
IEEE 802.3x Pause Frame for Full-Duplex
LED Indicators
• 1 x PoE IN (Green)
• 1 x LAN Data (Green)
• 1 x PoE OUT (Green)
Protection
ESD (Ethernet) : 6KV (TBD)
Surge (EFT for power) : 6KV (TBD)
Dimension
(W x D x H)
94 x 70 x 26 mm
Weight 215g
Power
Requirement
IEEE 802.3af compliant with voltage
within 44V-56V DC
Power
Consumption
2 Watts (system maximum)
Mechanical Metal / Wall Mountable
Cable TIA/EIA-568, Category 5/5e cable
Standards Conformance
Regulation
Compliance
FCC Part 15 Class A, CE
2. Hardware Description
2.1 Product Outlook
3. Hardware Installation
This product provides two different running speeds –
10Mbps, 100Mbps in the same device and automatically
distinguishes the speed of incoming connection.
This section describes the hardware features of POE-E101.
Before connecting any network device to the POE-E101,
read this chapter carefully.
3.1 Before Installation
Before your installation, it is recommended to check your
network environment. If there is any far away IEEE 802.3af
devices need to power on, the POE-E101 can provide you a
way to supply power for this Ethernet device conveniently
and easily.
The POE-E101 is installed between the PSE (Power Source
Equipment) and the PD (Powered Device); it is powered
by PSE and forwards the Ethernet data and remaining POE
powertothePD.ThePOE-E101doesn’trequireanexternal
power supply and it can be installed easily just plug and
play; that means the operator does not need to congure
the POE-E101. The POE-E101 injects power to the PDs
without affecting the data transmission performance. It
offers a cost effective and quick solution to extend power
and data an additional 100m.
Note
The POE-E101 can be installed with third-party
device if the device complied with IEEE 802.3af
standard.

Planet POE-E101 Specifications

General

Brand	Planet
Model	POE-E101
Category	Extender
Language	English