Platinum Tools VDV MapMaster User Manual

Voice, Data and Video Tester
outlined
Coax Type Belden P/N Center + Shield Maximum Length
RG-58A/U 8259 14.9Ω / 1,000 ft 6,710ft (2,045m)
9311 25.8Ω / 1,000ft 3,876ft (1,182m)
7806A 11.8Ω / 1,000ft 8,475ft (2,583m)
RG-59/U 9310 24.1Ω / 1,000ft 4,150ft (1,265m)
9259 23.5Ω / 1,000ft 4,255ft (1,297m)
8241A 49.7Ω / 1,000ft 2,010ft (613m)
9275 78.5Ω / 1,000 1,275ft (389m)
9659 17.6Ω / 1,000ft 5,682ft (1,732m)
RG-6/U 1694A 7.2Ω / 1,000ft 13,889ft (4,234m)
1152A 29.8Ω / 1,000ft 3,360ft (1,025m)
Mini Coax 9221 111Ω / 1,000ft 900ft (275m)
RG-11/U 1523A 15.1Ω / 1,000ft 6,623ft (2,019m)
U
S
A
M
A
D
E
I
N
T
H
E
M
A
D
E
I
N
T
H
E
U
S
A
www.platinumtools.com
©2011 Platinum Tools Inc. All rights reserved. 1/11
®
Instruction Sheet: P/N T119
GENERAL SPECIFICATIONS
The Platinum Tools, VDV MapMaster™ is a portable voice-data-video
cable tester. It tests and troubleshoots RJ11, RJ12, RJ45 and F-conector
terminated cables and provides built-in tone generation for cable tracing.
•Dimensions: 6.4˝ x 2.8˝ x 1.4˝ (16.3 x 7.1 x 3.6 cm)
•Weight: 9.0 oz. (256 grams) with battery and remote
•Operating Temperature: 0˚C/32˚F to 50˚C/122˚F
•Humidity: 10% to 90%, non-condensing
•Maximum Voltage between any two connector pins without damage:
RJ Jack: 66V DC or 55V AC
F-Connector: 50V DC or AC
•Battery Life: 9V alkaline battery typical
Standby: 4 years
Active: 425 hours
•Cable Types: Shielded or Unshielded; Cat7, Cat6x, Cat5e,
Cat5, Cat4, Cat3, Coax
•Maximum RJ Cable Length: 0 to 1,000 feet (305 meters)
•Minimum Cable Length for Split Pair Detection:
1.5 feet (0.5 meters)
•Maximum Coax Cable Length:
BATTERY REPLACEMENT
1) Remove single screw in the middle of the back
of the VDV MapMaster™ with a #1 Phillips head
screwdriver. Remove the battery door.
2) Remove the old battery and disconnect
battery cable.
3) Replace with an ANSI 1604A, 9 volt alkaline
battery (Energizer 522, Duracell Mn1604). Reattach
cable and insert into battery compartment.
4) Replace battery door and screw.
DO NOT OVERTIGHTEN!
WARNINGS
To ensure safe operation and service of the tester, follow these instructions.
Failure to observe these warnings can result in severe injury or death.
•TheVDVMapMaster™isdesignedforuseonunenergizedcabling
systems. Connecting the VDV MapMaster to live AC power may
damage it and pose a safety hazard for the user.
•PoorlyterminatedRJplugshavethepotentialtodamagethejacksonthe
VDV MapMaster™. Visually inspect an RJ plug before inserting it into the
tester. The contacts should always be recessed into the plastic housing
of the plug. Plugging 6-position plugs into the 8-position jack on the
tester has the potential to damage the outermost contacts of the jack
unless the plug is specifically designed for that purpose.
1

Platinum Tools VDV MapMaster Specifications

General

Model	VDV MapMaster
Manufacturer	Platinum Tools
Type	Cable Tester
Tone Generator	Yes
Battery Type	9V
Testing Capabilities	continuity, opens, shorts, miswires
Supported Cable Types	RJ45, RJ11
Function	Cable testing and troubleshooting
Test Types	Wiremap, Continuity, Open, Short, Miswire
Power Source	Battery

Summary

General Specifications

Physical and Environmental Specifications

Details dimensions, weight, operating temperature, and humidity for the VDV MapMaster.

Electrical and Battery Specifications

Covers maximum voltage tolerance and battery life expectancy for the VDV MapMaster.

Cable Compatibility and Length Limits

Lists supported cable types and maximum/minimum length specifications for testing.

Battery Replacement

Battery Replacement Procedure

Step-by-step instructions for replacing the 9V battery in the VDV MapMaster.

Display and Indicator Guide

Test Mode and Cable Status Indicators

Explains indicators for test mode, cable pass/fail, faults, and shielded status.

Wire Mapping and Remote Identification

Details tester/remote wire map display and remote location/ID.

System Warnings and Indicators

Covers battery low alert and voltage detection warning indicators.

Keypad Controls and Functions

Voice and Video Test Modes

Describes how to use the Voice and Video buttons for testing, including continuous mode.

Data and Tone Generation

Explains Data button function and tone generation for cable tracing.

Off/ID and Continuous Mode

Details powering off the device, initiating ID test mode, and continuous testing.

Wiring and Display Examples

T568A UTP Wiring Examples

Illustrates correctly wired T568A UTP cables and common wiring errors like split pairs.

Cable Fault Display Examples

Shows how shorts, opens, and miswires are displayed on the VDV MapMaster.

Master Remote and Accessories

Master Remote Usage

Explains the function of the Master Remote for network testing and mapping.

Available Accessories

Lists and describes various accessories for enhancing cable testing capabilities.