Why does my Polaris Widetrack LX have erratic engine RPM during acceleration?
J
Jeffery MyersSep 5, 2025
If your Polaris Offroad Vehicle experiences erratic engine RPM during acceleration or load variations:
* **Drive Clutch Binding:** If the drive clutch is binding, disassemble it to inspect the shift weights for wear and free operation. Consult your dealer.
* **Driven Clutch Malfunction:** If the driven clutch is malfunctioning, replace the ramp buttons and rollers. Consult your dealer.
H
hlaneSep 4, 2025
What to do if my Polaris Offroad Vehicle fails to move?
M
Melissa GriffinSep 4, 2025
If your Polaris Offroad Vehicle fails to move, consider the following potential issues:
* **Clutch Jammed:** If the clutch is jammed, with a twisted belt, broken spring, stuck weights, or lubrication issues, consult your dealer.
* **Track Jammed:** A foreign object might be caught in the track, or the rail slide could be melted to the track clips due to lack of lubrication. Also, the machine may be frozen to the ground, or the track may be iced up.
* **Chaincase Issues:** If the chaincase sprocket or chain is jammed or broken, with a loose or broken chain, or a loose chain tightener, consult your dealer.
D
Denise WhiteSep 3, 2025
Why does the rear suspension on my Polaris Widetrack LX Offroad Vehicle ride too stiff?
J
jyoungSep 3, 2025
If the rear suspension on your Polaris Offroad Vehicle rides too stiff, here are a few things to check:
* Check for binding suspension components and grease all pivot points.
* Verify the sag dimension and adjust the torsion spring blocks or install optional torsion springs to achieve the correct sag dimensions.
* Decrease shock compression damping.
B
Brendan LopezSep 1, 2025
What causes harsh drive clutch engagement on a Polaris Offroad Vehicle?
K
Kimberly MitchellSep 2, 2025
If your Polaris Offroad Vehicle has harsh drive clutch engagement, it could be due to:
* **Worn Drive Belt:** The drive belt may be worn or too narrow. Replace the drive belt.
* **Excessive Belt/Sheave Clearance:** Consult your dealer to address excessive belt/sheave clearance.
M
Mrs. Lori SchultzAug 31, 2025
Why does the drive belt on my Polaris Widetrack LX Offroad Vehicle turn over?
C
cbakerAug 31, 2025
If the drive belt on your Polaris Offroad Vehicle turns over, here's what you should investigate:
* **Wrong Belt:** The belt might not be the correct one for your vehicle. Replace the drive belt.
* **Clutch Alignment:** The clutch alignment could be out of specification. Adjust the alignment offset.
* **Engine Mount:** A broken or loose engine mount can cause this issue. Inspect, adjust, or replace it.
R
Ronald PowellAug 30, 2025
What causes a Polaris Widetrack LX Offroad Vehicle engine to continually backfire?
R
rmannAug 30, 2025
If your Polaris Offroad Vehicle engine continually backfires, consider these possible causes:
* **Faulty Spark Plugs:** Try changing the spark plugs.
* **Carburetor Issues:** There might be dirt or ice in the fuel system. Use a deicer with non-ethanol fuel for protection against fuel line icing.
O
oliverhaleyAug 29, 2025
How to troubleshoot poor engine performance on a Polaris Widetrack LX?
K
Kelsey FoleyAug 29, 2025
If you're experiencing poor engine performance with your Polaris Offroad Vehicle, check the following: carb and choke synchronization, fouled plugs, debris in the carbs, and water, ice, or dirt in the gas tank or fuel line.
G
George BarronAug 27, 2025
Why does my Polaris Widetrack LX dart from side to side?
E
Erica KnappAug 27, 2025
If your Polaris Offroad Vehicle darts from side to side, check the following:
* Ensure the skis are properly aligned.
* Check for binding front suspension shafts and steering components, and grease all pivot points after elevating the front of the machine.
* Make sure the skags are straight on the skis.
C
Crystal JacksonAug 27, 2025
Why does the front end of my Polaris Widetrack LX Offroad Vehicle push?
B
Brenda JohnsonAug 27, 2025
If your Polaris Offroad Vehicle's front end pushes, consider the following:
* Check for worn skags.
* Inspect for binding in the front suspension shafts and steering components, and grease all pivot points after elevating the front of the machine.
* Verify the sag dimension and adjust the torsion spring blocks or install optional torsion springs to achieve the correct sag dimensions.
* Increase the IFS preload.
T
Theresa WardAug 25, 2025
Why is the steering on my Polaris Offroad Vehicle so heavy?
J
jimenezheatherAug 26, 2025
If the steering on your Polaris Offroad Vehicle feels heavy, here are a few things you can check:
* Inspect the skags and skis for any damage.
* Look for any binding in the front suspension shafts and steering components. Grease all pivot points after elevating the front of the machine.
* Verify the sag dimension and adjust the torsion spring blocks or install optional torsion springs to achieve the correct sag dimensions.
* Decrease the IFS preload.
To Next Page
General
