cessible nooks. While it sanitises, it also elim-
inates smells.
Instructions for use :
Fit the disposable bottle into the delivery de-
vice following the instructions in paragraph
“DISPOSABLE BOTTLE OF HPMED”.
Switch on the SANI SYSTEM POLTI ma-
chine following the manufacturer’s instruc-
tions. Once the system is ready, distribute the
steam and HPMED sanitising agent. Mixed
with the steam, the product will dry within 30
seconds to one minute, depending on the en-
vironmental conditions.
Warnings :
Keep out of the reach of children. Do not in-
gest. In case of contact with eyes, rinse with
plenty of water and seek medical advice.
A safety data sheet is available for profes-
sional users.
For professional use only.
HPMED is a cleaning sanitisin product for
hard surfaces. Contains <5% non-ionic sur-
factant. (EEC Reg. 648/2004).
P
P
R
R
E
E
P
P
A
A
R
R
I
I
N
N
G
G
F
F
O
O
R
R
U
U
S
S
E
E
• Unscrew the cap (G) from the tank and fill
the tank with about 4.5l of normal tap water.
Disconnecting of the device from the power
mains before filling is recommended.
• Fit the carrier grip as shown in Fig.1, tighte-
ning the two screws on the rear of the grip
to secure it in place.
• Insert the tube-holder rod (L) into its hole
(Fig.2).
• Plug the power cable (H) into the panel-
type socket on the rear of the device. Plug
the connector on the other end of the power
cord into a suitable socket with an earth
connection.
•
Fit the disposable bottle into the delivery de-
vice following the instructions in paragraph
“DISPOSABLE BOTTLE OF HPMED”.
L
L
O
O
G
G
I
I
N
N
• Turn the ON-OFF switch (A) to position "I".
• The date and time will appear on the dis-
play (C). Press “OK” on the numerical key-
pad (B) to confirm. If the date and time are
not displayed automatically, it will be neces-
sary to enter them by hand using the nu-
merical keypad and then pressing “OK” to
confirm.
• The prompt “PRINT last logout?” will ap-
pear on the display. Press “OK” on the nu-
merical keypad if you wish to print the lo-
gout summary of the last work session.
Otherwise press “CANC”.
• The device will start up and the word LO-
GIN will appear on the display.
• Insert the CARD (U) into the slot provided
for it (D5).
• The following information will appear:
“HEATING” (flashing) to indicate that the de-
vice is in the heating stage.
Once the correct pressure is reached, the
word “READY” will appear to show that the
device is ready for use.
The indication IDXX will also appear (XX cor-
responds to the number of the CARD inserted
at the time).
N.B.: Do not remove the CARD from the
slot during use.
If the CARD is removed during use, the ma-
chine will stop working and the message
“LOCKED - INSERT CARD IDXX” will appear
on the display. To unlock the machine and re-
sume work, it is necessary to insert the same
card used earlier to log in. The work data will
remain stored in the memory.
The CARDS supplied with the machine are
already configured and will work only in the
machine with which they were supplied. If
new cards are purchased, they will have to be
initialized. To do this, proceed as described in
the section “INITIALISING NEW CARDS”.
• Once you have logged in, the following in-
formation will appear on the display:
“Prog:__” It is necessary to insert the number
of the programme you wish to use. The pro-
gramme numbers have two digits.
There are four pre-set programmes:
00, 01, 02 and 03.
Enter the number of the chosen programme
via the numerical keypad and press OK.
If you have entered the wrong programme
number, you can delete the entry with the
CANC key.
SANI SYSTEM CHECK
45
E
E
N
N
G
G
L
L
I
I
S
S
H
H
SANI SYSTEM CHECK M0S08111 2O08:A5 31/07/2008 11.27 Pagina 45
To Next Page
Loading...
