Poulan Pro 401115 User Manual (English)

Questions and Answers:

K
Kyle CarterAug 18, 2025
How to fix Poulan Pro Lawn Mower that will not start?
- C
  Casey SullivanAug 18, 2025
  If your Poulan Pro Lawn Mower won't start, possible causes include being out of fuel (fill the fuel tank), improper choking (consult the Operation section for starting procedures), a flooded engine (wait a few minutes before restarting), a bad spark plug (replace it), a dirty air filter (clean or replace it), or a dirty fuel filter (replace it). Other potential issues are water in the fuel (empty the tank and carburetor, refill with fresh gasoline, and replace the fuel filter), loose or damaged wiring (check all wiring), a carburetor out of adjustment (see the Service Adjustments section), or engine valves out of adjustment (contact an authorized service center).
A
amanda65Aug 21, 2025
How to troubleshoot hard starting Poulan Pro Lawn Mower?
- P
  Paige RoseAug 21, 2025
  If your Poulan Pro Lawn Mower is hard to start, consider these possible causes: * A dirty air filter (clean or replace it). * A bad spark plug (replace it). * A weak or dead battery (recharge or replace it). * A dirty fuel filter (replace it). * Stale or dirty fuel (empty the tank and refill with fresh, clean gasoline). * Loose or damaged wiring (check all wiring). * Carburetor out of adjustment (see the Service Adjustments section). * Engine valves out of adjustment (contact an authorized service center).
B
bjohnsAug 23, 2025
What to do if Poulan Pro Lawn Mower engine clicks but will not start?
- J
  joseph85Aug 23, 2025
  If the engine of your Poulan Pro Lawn Mower clicks but won't start, it could be due to a weak or dead battery (recharge or replace it), corroded battery terminals (clean them), loose or damaged wiring (check all wiring), or a faulty solenoid or starter (check or replace them).
T
taylormorrisonAug 26, 2025
Why Poulan Pro Lawn Mower engine will not turn over?
- N
  nicholas92Aug 26, 2025
  If your Poulan Pro Lawn Mower engine will not turn over, ensure the clutch/brake pedal is depressed. Also, disengage the attachment clutch. Other potential causes include a weak or dead battery (recharge or replace it), a blown fuse (replace it), corroded battery terminals (clean them), loose or damaged wiring (check all wiring), a faulty ignition switch (check or replace it), a faulty solenoid or starter (check or replace them). For faulty operator presence switch(es), contact an authorized service center.
V
Vincent CrawfordAug 28, 2025
What causes Poulan Pro Lawn Mower blades will not rotate?
- M
  Michele HawkinsAug 28, 2025
  If your Poulan Pro Lawn Mower blades won't rotate, check for an obstruction in the clutch mechanism and remove it. Also, inspect the mower drive belt for wear or damage and replace if necessary. Additionally, check the idler pulley and blade mandrel for freezing and replace if needed.
R
Robert FarmerAug 30, 2025
Why Poulan Pro Lawn Mower has poor cut - uneven?
- T
  Thomas GravesAug 30, 2025
  If your Poulan Pro Lawn Mower provides a poor and uneven cut, replace the blade or tighten the blade bolt if the blade is worn, bent, or loose. Level the mower deck. Clean the underside of the mower housing to remove any buildup of grass, leaves, and trash. Replace the blade mandrel if it's bent. Clean around the mandrels to open vent holes if they are clogged.
J
Jeffrey JohnsonSep 4, 2025
How to improve Poulan Pro Lawn Mower poor grass discharge?
- P
  pamela32Sep 5, 2025
  If your Poulan Pro Lawn Mower has poor grass discharge, ensure the throttle control is in the “FAST” position and shift to a slower speed if you're traveling too fast. Allow the grass to dry before mowing if it's wet. Also, level the mower deck and check the tires for proper air pressure. Other possible causes include a worn, bent, or loose blade (replace/sharpen and tighten), buildup of grass, leaves, and trash under the mower (clean the underside), a worn mower drive belt (replace it), improperly installed blades (reinstall sharp edge down), improper blades used (replace with correct blades), or clogged mower deck vent holes (clean around mandrels).
N
Natasha Williams DDSSep 7, 2025
How to reduce excessive vibration in Poulan Pro Lawn Mower?
- J
  Joshua GuerreroSep 7, 2025
  If your Poulan Pro Lawn Mower has excessive vibration, replace the blade or tighten the blade bolt if the blade is worn, bent, or loose. Replace the blade mandrel if it's bent. Also, tighten any loose parts and replace any damaged parts.
S
Stephanie DyerSep 10, 2025
How to fix Poulan Pro Lawn Mower headlight(s) not working?
- P
  Patricia AdamsSep 10, 2025
  If the headlight(s) on your Poulan Pro Lawn Mower aren't working, first, ensure the light switch is “ON.” If not, turn it on. If the bulb(s) or lamp(s) are burned out, replace them. Check or replace the light switch if it's faulty. Inspect the wiring and connections for looseness or damage. Finally, replace the fuse if it's blown.
G
grantpaulaSep 12, 2025
What to do if Poulan Pro Lawn Mower engine dies when tractor is shifted into reverse?
- B
  Brian SimpsonSep 12, 2025
  If your Poulan Pro Lawn Mower engine dies when shifted into reverse, ensure the Reverse Operation System (ROS) is turned "ON" while the mower or other attachment is engaged by turning the ignition key to the ROS "ON" position.