Poulan Pro PP175A42 User Manual (English)

Questions and Answers:

J
Jeremy JarvisAug 19, 2025
How to fix Poulan Pro PP175A42 that will not start?
- W
  William CharlesAug 20, 2025
  If your Poulan Pro Lawn Mower won't start, several factors could be the cause. First, make sure the fuel tank is full. If that's not the issue, ensure the engine is choked properly, as described in the Operation section. If the engine is flooded, wait a few minutes before trying again. Other potential causes include a bad spark plug (replace it), a dirty air filter (clean or replace it), a dirty fuel filter (replace it), or water in the fuel (empty the tank and carburetor, refill with fresh gasoline, and replace the fuel filter). Also, check for loose or damaged wiring. If none of these solutions work, the engine valves may be out of adjustment, and you should contact an authorized service center.
J
Julia WilsonAug 21, 2025
Why is my Poulan Pro PP175A42 hard to start?
- R
  Robert AndersenAug 22, 2025
  If your Poulan Pro Lawn Mower is hard to start, consider these possibilities: The air filter might be dirty, so clean or replace it. The spark plug could be bad, requiring replacement. A weak or dead battery could be the issue; recharge or replace it as necessary. Also, check the fuel filter; if it's dirty, replace it. Stale or dirty fuel can also cause problems, so empty the fuel tank and refill it with fresh, clean gas. Finally, inspect the wiring for any loose connections or damage. If these steps don't resolve the issue, the engine valves may need adjustment by an authorized service center.
C
christopherevansAug 25, 2025
What to do if Poulan Pro PP175A42 Lawn Mower engine will not turn over?
- L
  Leah SchmidtAug 25, 2025
  If the engine of your Poulan Pro Lawn Mower won't turn over, make sure you're depressing the brake pedal. Also, ensure the attachment clutch is disengaged. A weak or dead battery could be the culprit, so recharge or replace it. Check for a blown fuse and replace it if necessary. Clean any corrosion from the battery terminals. Inspect all wiring for looseness or damage. If the problem persists, the ignition switch, solenoid, or starter might be faulty and need checking or replacement. If those don't solve the problem, contact an authorized service center to inspect the operator presence switches.
A
Ashley SullivanAug 26, 2025
Why does my Poulan Pro PP175A42 engine click but not start?
- R
  Rachel HudsonAug 26, 2025
  If your Poulan Pro Lawn Mower engine clicks but doesn't start, the battery may be weak or dead, requiring a recharge or replacement. Corroded battery terminals can also cause this issue, so clean them thoroughly. Inspect the wiring for any loose connections or damage. If these steps don't resolve the problem, the solenoid or starter might be faulty and need to be checked or replaced.
M
Mrs. Mary MayAug 27, 2025
What to do if Poulan Pro PP175A42 Lawn Mower blades will not rotate?
- Z
  zturnerAug 28, 2025
  If the mower blades of your Poulan Pro Lawn Mower will not rotate, there might be an obstruction in the clutch mechanism; remove it. The mower drive belt could be worn or damaged, so replace it. A frozen idler pulley or blade mandrel could also be the cause, requiring replacement.
A
amycortezSep 1, 2025
How to fix Poulan Pro PP175A42 Lawn Mower poor uneven cut?
- R
  rmeyerSep 1, 2025
  If your Poulan Pro Lawn Mower is leaving an uneven cut, the blade might be worn, bent, or loose; replace the blade and tighten the blade bolt. Check if the mower deck is level and adjust it if necessary. Buildup of grass, leaves, or trash under the mower can also cause an uneven cut, so clean the underside of the mower housing. Additionally, inspect the blade mandrel for bending and replace it if needed. Finally, check for clogged mower deck vent holes and clean around the mandrels to open them.
B
Bradley JonesSep 2, 2025
Why Poulan Pro PP175A42 Lawn Mower has poor grass discharge?
- R
  Roger JonesSep 3, 2025
  If your Poulan Pro Lawn Mower has poor grass discharge, ensure the engine speed isn't too slow by placing the throttle control in the 'FAST' position. If you're moving too fast, shift to a slower speed. Wet grass can also cause poor discharge, so allow the grass to dry before mowing. Check if the mower deck is level and adjust it if necessary. Make sure the tire air pressure is correct and even. Inspect the blade for wear, bending, or looseness, and replace or tighten it as needed. Clean any buildup of grass, leaves, or trash under the mower. If the mower drive belt is worn, replace it. Ensure the blades are installed with the sharp edge down. If improper blades are used, replace them with the blades listed in the parts manual. Finally, clear any clogged mower deck vent holes.
C
Colin MolinaSep 4, 2025
What causes excessive vibration in Poulan Pro PP175A42?
- A
  Ashley DuncanSep 4, 2025
  If your Poulan Pro Lawn Mower is experiencing excessive vibration, the blade may be worn, bent, or loose. Replace the blade and tighten the blade bolt. The blade mandrel might also be bent, requiring replacement. Check for any loose or damaged parts and tighten or replace them as necessary.
K
Kelly WilliamsSep 6, 2025
Why Poulan Pro PP175A42 headlights are not working?
- A
  Andrew HallSep 7, 2025
  If the headlight(s) on your Poulan Pro Lawn Mower aren't working, first ensure the switch is turned 'ON'. If that's not the issue, the bulb(s) or lamp(s) may be burned out and need replacement. A faulty light switch could also be the cause, so check or replace it. Inspect the wiring and connections for looseness or damage. Finally, check the fuse and replace it if it's blown.
D
David RobbinsSep 8, 2025
What causes Poulan Pro Lawn Mower battery to not charge?
- C
  Calvin WoodsSep 8, 2025
  If the battery of your Poulan Pro Lawn Mower will not charge, it could be due to bad battery cells, requiring a battery replacement. Poor cable connections can also prevent charging, so check and clean all connections. If equipped, a faulty regulator or alternator might be the cause, and you should replace them.

Poulan Pro PP175A42 Specifications

General

Engine Type	4-Cycle
Cutting Width	42 inches
Deck Material	Steel
Engine	Briggs & Stratton
Cutting Height	1.5 to 4 inches

Summary

OPERATOR'S MANUAL

SAFETY RULES

I. CHILDREN

Safety instructions and age recommendations for children operating equipment.

II. GENERAL OPERATION

General operating instructions for the tractor.

III. SLOPE OPERATION

Operating safely on slopes, including warnings and precautions.

IV. TOWING

Guidelines and safety precautions for towing attachments.

V. SERVICE

General service recommendations and safety.

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

SUPPORT / HELP

UNASSEMBLED PARTS

Steering Wheel Parts

Lists all parts included for the steering wheel assembly.

Seat Parts

Lists all parts included for the seat assembly.

Battery Parts

Lists all parts related to the tractor battery.

Keys

Lists the tractor keys.

Oil Drain Extension

Lists the oil drain extension part.

Slope Sheet

Lists the included slope sheet.

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

Lists all necessary tools for the assembly process.

TRACTOR UNPACKING

Instructions for safely removing the tractor from its carton.

CONNECT BATTERY

Step-by-step guide for connecting the tractor battery.

INSTALL STEERING WHEEL

Instructions for installing the tractor's steering wheel.

INSTALL SEAT

Steps for correctly installing the tractor seat.

ROLL TRACTOR OFF SKID

Procedure for safely moving the tractor off its shipping skid.

CHECK TIRE PRESSURE

Ensuring tires are properly inflated for optimal performance.

CHECK DECK LEVELNESS

How to verify the mower deck is level.

CHECK BELT POSITION

Verifying the correct routing of mower and drive belts.

CHECK BRAKE SYSTEM

How to check the functionality of the tractor's brake system.

ASSEMBLY COMPLETION CHECKLIST

Final checks before operating the tractor after assembly.

OPERATION

UNDERSTANDING TRACTOR SYMBOLS

Explains symbols used on the tractor and in the manual.

UNDERSTANDING HAZARD SYMBOLS

Explains hazard symbols like Danger, Warning, and Caution.

KNOW YOUR TRACTOR

Familiarization with tractor controls and their locations.

HOW TO USE YOUR TRACTOR

General guidance on operating the tractor safely.

TO SET PARKING BRAKE

Instructions for engaging the parking brake.

STOPPING THE TRACTOR

Procedures for stopping mower blades, ground drive, and engine.

TO USE THROTTLE CONTROL

How to operate the throttle for engine speed control.

TO MOVE FORWARD AND BACKWARD

How to control tractor movement using drive pedals.

TO ADJUST MOWER CUTTING HEIGHT

How to set the desired mower cutting height.

TO ADJUST GAUGE WHEELS

How to adjust the mower gauge wheels for proper leveling.

TO OPERATE MOWER

How to engage and operate the mower deck.

TO STOP MOWER BLADES

Instructions on how to stop the mower blades.

TO OPERATE ON HILLS

Safety and operational guidelines for slopes.

REVERSE OPERATION SYSTEM (ROS)

Explanation of the Reverse Operation System feature.

USING THE REVERSE OPERATION SYSTEM

How to safely use the ROS feature when mowing in reverse.

TOWING CARTS & OTHER ATTACHMENTS

Guidelines for towing carts and other attachments.

BEFORE STARTING THE ENGINE

Checks and preparations before starting the engine.

CHECK ENGINE OIL LEVEL

How to check the engine oil level.

ADD GASOLINE

Instructions on how to add gasoline to the fuel tank.

TO START ENGINE

Step-by-step instructions for starting the tractor engine.

AUTOMATIC TRANSMISSION WARM UP

Procedure for warming up the transmission in cold weather.

MOWING TIPS

Advice for optimal mowing performance and safety.

MAINTENANCE

MAINTENANCE SCHEDULE

Schedule of required maintenance tasks and frequencies.

GENERAL RECOMMENDATIONS

General advice for maintaining the tractor and warranty.

BEFORE EACH USE CHECKS

Daily checks to perform before operating the tractor.

LUBRICATION CHART

Diagram and guide for lubrication points.

BRAKE OPERATION CHECK

How to check the tractor's brake system.

TIRE MAINTENANCE

Advice for maintaining tractor tires.

OPERATOR PRESENCE & ROS SYSTEM CHECKS

Verifying safety system functionality.

BLADE CARE AND REMOVAL

Instructions for mower blade maintenance and replacement.

BATTERY MAINTENANCE AND CLEANING

How to care for and clean the tractor battery.

V-BELTS AND TRANSAXLE MAINTENANCE

V-belt inspection and transaxle maintenance information.

ENGINE LUBRICATION AND OIL CHANGE

Engine oil recommendations and changing procedure.

AIR FILTER AND AIR SCREEN CLEANING

Maintenance of the air filter and screen.

ENGINE COOLING SYSTEM AND MUFFLER MAINTENANCE

Cleaning cooling system and inspecting muffler.

SPARK PLUGS AND IN-LINE FUEL FILTER REPLACEMENT

Replacing spark plugs and the in-line fuel filter.

GENERAL CLEANING PROCEDURES

Instructions for cleaning the tractor and its various parts.

SERVICE AND ADJUSTMENTS

TO REMOVE MOWER

Step-by-step instructions for removing the mower deck.

TO INSTALL MOWER

Step-by-step instructions for installing the mower deck.

MOWER DECK ATTACHMENT STEPS

Detailed steps for attaching mower components to the tractor.

BELT ROUTING AND GAUGE WHEEL ADJUSTMENT

Checking belt routing and adjusting mower gauge wheels.

TO LEVEL MOWER: SIDE-TO-SIDE ADJUSTMENT

How to adjust mower deck side-to-side leveling.

TO LEVEL MOWER: FRONT-TO-BACK ADJUSTMENT

How to adjust mower deck front-to-back leveling.

TO REPLACE MOWER BLADE DRIVE BELT

Instructions for replacing the mower blade drive belt.

TO REPLACE MOTION DRIVE BELT

Instructions for replacing the motion drive belt.

TO CHECK BRAKE

Procedure for checking the tractor's brake system.

TO REMOVE AND INSTALL WHEELS

Procedures for removing and installing tractor wheels.

STEERING WHEEL ALIGNMENT

How to adjust the steering wheel alignment.

FRONT WHEEL ALIGNMENT

Information on front wheel toe-in/camber.

STARTING ENGINE WITH A WEAK BATTERY

Procedure for jump-starting the tractor.

REPLACING BATTERY

Step-by-step guide for battery replacement.

HOOD AND GRILL ASSEMBLY REMOVAL

How to remove the tractor's hood and grill assembly.

HEADLIGHT BULB REPLACEMENT

How to replace a headlight bulb.

ENGINE CONTROL CABLE ADJUSTMENTS

Adjusting throttle and choke control cables.

STORAGE

TRACTOR STORAGE PREPARATION

Steps to prepare the tractor for long-term storage.

BATTERY STORAGE GUIDELINES

How to properly store the tractor battery.

ENGINE FUEL SYSTEM STORAGE

Preparing the fuel system for storage.

ENGINE OIL AND CYLINDER STORAGE

Engine oil and cylinder preparation for storage.

GENERAL STORAGE TIPS

Additional tips for storing the tractor and related components.

TROUBLESHOOTING

ENGINE STARTING PROBLEMS

Troubleshooting issues related to starting the engine.

ENGINE PERFORMANCE ISSUES

Troubleshooting problems like loss of power or excessive vibration.

OPERATOR PRESENCE SYSTEM FAULT

Troubleshooting engine running after operator leaves seat.

CUTTING AND MOWER OPERATION ISSUES

Troubleshooting uneven cuts, blade rotation, or poor discharge.

ELECTRICAL AND DRIVE SYSTEM ISSUES

Troubleshooting headlights, battery charging, and loss of drive.

ENGINE SHUTDOWN AND REVERSE ISSUES

Troubleshooting engine backfiring and dying in reverse.

Related product manuals

Poulan Pro PPR20H42STB

48 pages

Poulan Pro PP175A42 User Manual

Table of Contents

Questions and Answers:

Poulan Pro PP175A42 Specifications

Summary

OPERATOR'S MANUAL

SAFETY RULES

I. CHILDREN

II. GENERAL OPERATION

III. SLOPE OPERATION

IV. TOWING

V. SERVICE

PRODUCT SPECIFICATIONS

CUSTOMER RESPONSIBILITIES

SUPPORT / HELP

UNASSEMBLED PARTS

Steering Wheel Parts

Seat Parts

Battery Parts

Keys

Oil Drain Extension

Slope Sheet

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

TRACTOR UNPACKING

CONNECT BATTERY

INSTALL STEERING WHEEL

INSTALL SEAT

ROLL TRACTOR OFF SKID

CHECK TIRE PRESSURE

CHECK DECK LEVELNESS

CHECK BELT POSITION

CHECK BRAKE SYSTEM

ASSEMBLY COMPLETION CHECKLIST

OPERATION

UNDERSTANDING TRACTOR SYMBOLS

UNDERSTANDING HAZARD SYMBOLS

KNOW YOUR TRACTOR

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

STOPPING THE TRACTOR

TO USE THROTTLE CONTROL

TO MOVE FORWARD AND BACKWARD

TO ADJUST MOWER CUTTING HEIGHT

TO ADJUST GAUGE WHEELS

TO OPERATE MOWER

TO STOP MOWER BLADES

TO OPERATE ON HILLS

REVERSE OPERATION SYSTEM (ROS)

USING THE REVERSE OPERATION SYSTEM

TOWING CARTS & OTHER ATTACHMENTS

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

ADD GASOLINE

TO START ENGINE

AUTOMATIC TRANSMISSION WARM UP

MOWING TIPS

MAINTENANCE

MAINTENANCE SCHEDULE

GENERAL RECOMMENDATIONS

BEFORE EACH USE CHECKS

LUBRICATION CHART

BRAKE OPERATION CHECK

TIRE MAINTENANCE

OPERATOR PRESENCE & ROS SYSTEM CHECKS

BLADE CARE AND REMOVAL

BATTERY MAINTENANCE AND CLEANING

V-BELTS AND TRANSAXLE MAINTENANCE

ENGINE LUBRICATION AND OIL CHANGE

AIR FILTER AND AIR SCREEN CLEANING

ENGINE COOLING SYSTEM AND MUFFLER MAINTENANCE

SPARK PLUGS AND IN-LINE FUEL FILTER REPLACEMENT

GENERAL CLEANING PROCEDURES

SERVICE AND ADJUSTMENTS

TO REMOVE MOWER

TO INSTALL MOWER

MOWER DECK ATTACHMENT STEPS

BELT ROUTING AND GAUGE WHEEL ADJUSTMENT

TO LEVEL MOWER: SIDE-TO-SIDE ADJUSTMENT

TO LEVEL MOWER: FRONT-TO-BACK ADJUSTMENT