Poulan Pro PR100 User Manual

Poulan Pro PR100

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

OWNER'S MANUAL

MODEL NUMBER:

PR100

SNOW THROWER

Always Wear Eye Protection During Operation

IMPORTANT MANUAL Do Not Throw Away

WARNING:

Read the Owner's Manual and

fol low all Warnings and Safety

In struc tions. Fail ure to do so

can result in serious injury.

114 07 34-24 13.07.17 MJ

Printed in the U.S.A.

Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.

The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.

Table of Contents

Questions and Answers:

C
Colleen AndersonAug 13, 2025
Why Poulan Pro PR100 does not start?
- T
  traviskellyAug 13, 2025
  Your Poulan Pro Snow Blower might not start due to several reasons: the safety ignition key may not be inserted (insert it); the fuel tank may be empty (refill with fresh gasoline); the ON/OFF switch may be OFF (move it to the ON position); the choke might be in the OFF position (move it to FULL); the engine might be flooded (wait a few minutes before restarting, without priming); the spark plug wire may be disconnected (connect it); the spark plug may be bad (replace it); the fuel may be stale or contain water (empty the fuel tank and carburetor, then refill with fresh gasoline); or the fuel line may be vapor locked (ensure the fuel line runs continuously down from the fuel tank to the carburetor).
R
reginafitzgeraldAug 16, 2025
What to do if Poulan Pro PR100 Snow Blower loses power?
- W
  Wendy SmithAug 16, 2025
  If your Poulan Pro Snow Blower loses power, check the following: ensure the spark plug wire is securely connected; reduce the speed and width of the snow swath; remove any ice or snow from the fuel tank cap; clean or replace a dirty or clogged muffler; clear any blockage from the muffler or carburetor air intake (make sure the engine is cool); and adjust the cable if the length is improper.
W
walkerbrittanyAug 20, 2025
Why Poulan Pro PR100 lights are not on?
- R
  Ryan AlvarezAug 20, 2025
  If the lights on your Poulan Pro Snow Blower are not on (if equipped), it could be due to the motor not running (start the engine); a loose wire connection (check the wire connections at the engine and both lights); or a burnt-out LED (replace the LED light module, as individual LEDs are not replaceable).
T
timothyperryAug 23, 2025
What to do if Poulan Pro PR100 loses snow discharge?
- V
  Vanessa WilsonAug 25, 2025
  If your Poulan Pro Snow Blower experiences loss of snow discharge or slowing of snow discharge, consider these potential issues: the belt may be worn (adjust the drive cable); the auger v-belt might be off the pulley (check and reinstall it) or worn (check and replace it); the discharge chute could be clogged (clean it); or the augers/impeller could be jammed (remove any debris).
R
Rachel SmithAug 28, 2025
Why Poulan Pro Snow Blower engine idles roughly?
- C
  Carolyn BowmanAug 28, 2025
  If your Poulan Pro Snow Blower engine idles or runs roughly, it could be due to: the choke being in the FULL position (move it to OFF); a blockage in the fuel line (clean it); stale or water-contaminated fuel (empty the tank and carburetor, refill with fresh gasoline); or belt stretch (replace the auger v-belt).
M
Melvin WilsonAug 31, 2025
What to do if Poulan Pro PR100 Snow Blower has excessive vibration?
- H
  hillannSep 1, 2025
  If your Poulan Pro Snow Blower has excessive vibration or handle movement, try the following: tighten all fasteners and replace any damaged augers or impeller; ensure the handles are locked into position; and tighten the adjustment lever nuts until the handle feels secure.
W
William JacksonSep 4, 2025
Why Poulan Pro PR100 rotator is hard to move?
- L
  Luis JohnsonSep 4, 2025
  If the rotator on your Poulan Pro Snow Blower is hard to move, there might be debris in the chute rotator mechanism (clean the internal parts) or the cables may be kinked or damaged (ensure cables are not kinked and replace damaged cables).
S
Shawn DavisSep 7, 2025
How to fix Poulan Pro PR100 recoil starter hard to pull?
- D
  deanjacobSep 7, 2025
  If the recoil starter on your Poulan Pro Snow Blower is hard to pull, it may be due to a frozen recoil starter, see “IF RECOIL STARTER HAS FROZEN” in the Operation section of this manual or the rope is interfering with components (recoil rope should not be touching any wires or hoses).

Poulan Pro PR100 Specifications

General

Clearing Width	21 in
Intake Height	13 in
Throw Distance	Up to 30 feet
Weight	110 lbs
Type	Single-Stage
Engine Displacement	208 cc
Engine Type	4-Cycle
Engine	Poulan Pro
Start Type	Manual
Fuel Tank Capacity	0.8 gallons

Related product manuals

Preview: Poulan Pro PR111

Poulan Pro PR111

Preview: Poulan Pro PR121ES

Poulan Pro PR121ES

Preview: Poulan Pro PR621

Poulan Pro PR621

Preview: Poulan Pro PR242

Poulan Pro PR242

Preview: Poulan Pro PR300

Poulan Pro PR300

Preview: Poulan Pro PR271

Poulan Pro PR271

Preview: Poulan Pro PR241

Poulan Pro PR241

Preview: Poulan Pro PR621ES

Poulan Pro PR621ES

Preview: Poulan Pro PR271ES

Poulan Pro PR271ES

Poulan Pro PR624ES

Poulan Pro PR5524ES