Power Fist 8643926 - User Manual

Questions and Answers

K
kirstenolsenJul 31, 2025
Why is there no pressure or low pressure in my Power Fist Pressure Washer?
- K
  kathywilsonJul 31, 2025
  If your Power Fist Pressure Washer is experiencing no pressure or low pressure, ensure the following: * The spray gun is set to high pressure. * The water supply meets the requirement of 4.2 GPM @ 20 psi. * Hose fittings are tightened and sealed with thread sealant tape if necessary. * The nozzle and water filter screen are free of obstructions. * The thermal relief valve is functioning correctly (replace if defective). * Air is purged from the hose. * The choke lever is in the 'NO CHOKE' position. * The throttle control lever is not in the fast position. * The high-pressure hose is under 100 ft.
J
Jamie RogersAug 4, 2025
What to do if the Power Fist 8643926 Pressure Washer pump will not draw chemical or detergent?
- B
  brittany82Aug 4, 2025
  If your Power Fist Pressure Washer pump isn't drawing chemicals or detergent, make sure of the following: * The spray gun is set to low pressure. * The chemical filter is clean. * The chemical screen is fully submerged in the chemical solution. * The chemical solution is diluted to the consistency of water. * The pressure hose is not excessively long; use a longer water supply hose instead. * If there is a chemical build-up in the chemical injector, have the parts cleaned or replaced by an authorized dealer.
C
Christina BurtonAug 8, 2025
Why is my Power Fist 8643926 Pressure Washer leaking oil at the pump?
- N
  nancy08Aug 9, 2025
  If your Power Fist Pressure Washer is leaking oil at the pump, check the following: * Tighten the drain plug. * Inspect and replace the drain plug O-ring and fill plug O-ring if worn. * Ensure the pump is not overfilled and contains the correct type and amount of oil. * Clean the vent plug; use an air hose to clear any blockage. Replace the vent plug if the problem continues. For worn oil seals, you should have the parts cleaned or replaced by an authorized dealer.
C
Cameron SaundersAug 12, 2025
How to fix water leaking at the spray gun/spray wand connection on a Power Fist 8643926?
- A
  Abigail VangAug 13, 2025
  If you experience water leaking at the spray gun/spray wand connection of your Power Fist Pressure Washer, check and replace the O-ring if it is worn or broken. Also, ensure that the hose connection is tightened.
N
nicole69Aug 17, 2025
Why does my Power Fist 8643926 Pressure Washer pump pulsate?
- L
  Lori VillegasAug 17, 2025
  If your Power Fist Pressure Washer pump pulsates, the nozzle might be obstructed.
M
moorejohnAug 22, 2025
What to do if water is leaking at the pump of my Power Fist 8643926?
- R
  Ronald GreenAug 22, 2025
  If water is leaking at the pump of your Power Fist Pressure Washer, tighten any loose connections. For issues such as worn piston packing, worn or broken O-rings, or pump head/tubes damaged from freezing, have the parts cleaned or replaced by an authorized dealer.
A
Amanda JohnsonAug 26, 2025
What to do if my Power Fist Pressure Washer has no or low pressure after a period of normal use?
- R
  rebecca13Aug 26, 2025
  For no or low pressure after a period of normal use of your Power Fist Pressure Washer, have parts cleaned or replaced by an authorized dealer. This applies to worn seals or packing, worn or obstructed valves, worn unloader piston, or a worn E-Z start valve.