PPA CODIGUS 4D PLUS User Manual

MAIN CHARACTERISTICS
• 4sectorswithand/orwirelessthatcanbearmedanddisarmed,
independently,byremotecontrol;
• Arm and disarm via remote control, keypad, telephone call or
auxiliaryinput(optionaldevice);
• Automaticarmintheabsenceofmovement,withprogrammabletime;
• Sectorshutdownafter4violations(programmable);
• Beepsforarming,disarmingandarmingfailure(programmable);
• Programmableinput,outputandsirentime;
• Pulsedialing(decadic)ortone(DTMF);
• Audibleorsilentpanicbyremotecontrol(pressedfor3seconds);
• Dialingupto6phonenumberswith22digitseach;
• Supportsupto80wirelessdevices,includingcontrolsandsensors;
• Lowbatterywarningforwirelesssensors(onlyforsensormodels
thathavethisfeature);
• Timedsectors(programmable);
• CongurableA/D(auxiliary)inputforpulseorhold;
• Telephonecallcommands:arming,disarming,statusandcommands
forLED/PGMoutput;
• 12VoltoutputforcongurableexternalLED/PGM;
• Automaticreset(programmable);
• Smartsectors(programmable).
ACESSING THE PROGRAMMING MODE
Inthismodeallthealarmparametersarecongured.Toaccess,make
suretheboardisdisarmedandtype:
# + installer password
Thefactorydefaultinstallerpasswordis4321.
After each command sequence, typed in the programming
(passwords,indexes,values,conrmation,etc.),theboardwillemit3
beeps,indicatingifthecommandortheprogrammingwasaccepted.
Ifthecommandiswrong,theboardwillsound1 long beep(error).
Whileinthismode,theLine LEDwillremainblinking.
Toexittheprogrammingmode, pressthe*keyuntiltheLine LED
stopsblinking.
Ifnokeyispressedforupto20 seconds,theboardwillautomatically
terminatetheprogrammingmode.
REGISTERING PHONES
Itallowstheregistrationofupto6 telephone numberswithupto22
digits each.The corresponding indices are: 01 to 06.
LOCAL CALLS:
Toregisterlocalphones,type:
#4321 01to06 Up22digits # #
prog.access Índex TelephoneNº Conrm OutProg
When entering a telefone number with all 22 digits, it is not
necesserrytopressconrmationkey#,sincethelastnumber(22º)
willcorrespondtotheendoftheindex.
CALLS BY PABX:
Intelephoneswitchboards(PABX),itisnecessarytoinputacommand
toaccesstheexternallineandtheninsertapauseinthedial.
In the example below, a telephone number will be registered via
extension,adding0(zero)andpauseof2secondsbeforethenumber.
Type:
#4321 01to06 0 E TelephoneNº # #
ProgAccess. Índex Up22digits Conrm Outprog.
TheEkeypausesfor2 seconds.Ifitisnecessarytogenerateapause
of6 seconds,forexample,presstheEkeypor3 times,intheposition
indicatedpreviouslyandsoon.
LONG DISTANCE CALLS:
Registeraphonefromanothercityorregion.Type:
#4321 01to06 0  Oper.Nº DDDNº Tel.Nº # #
ProgAccess. Index Up22dígits Conrm Outprog.
SPECIAL CALLS:
Somephoneoperatorsoerservicespackagesthatrequirethecode
to make cellular or long distance calls. In these case, is necessary
toprogramspecialdigitsbeforethedesirephonenumbersuchas,
*(asterisl)and#(ring).TheredigitsareenteredusingthePandF,
showinthetable.
Exemple:
#4321 01to06 P  Oper.Nº E Tel.Nº # #
ProgAccess. Index Up22digits Conrm Outprog.
KEY FUNCTION
E
Insertpauseof
2seconds
P
Insertthedigit*
inprogramming
F
Insertthedigit#
Inprogramming
DELETING TELEPHONES
Thereare2waystodeletearegisteredtelephone:
1.ª) Do not enter a number when accessing the desired index and
press# toconrm.THE CORRESPONDING ARE 01 TO 06.
Exemple:
#4321 01to06 # #
ProgAccess. Índex Apaga Outprog.
2.ª)Pressthekey*inthetelephonenumberposition.
#4321 01to06 * # #
ProgAccess. Index Tel.Nº Apaga Outprog.
PS:The phones must be deleted one at a time by accessing index
by index.
CHANGE PASSWORD
INSTALLER PASSWORD:
Itisrequiredtoentertheprogrammingmode.Thefactorysettingis
4321.Changetoanotheroneofyourchoice.
Forchange,type:
#4321 07 4digits 3beeps #
ProgAccess. Index Newpassword Conrmation Outprog.
USER PASSWORD:
Usedtoarm,disarmandannulsectors.Thefactorydefaultis1234.
Changetoanotheroneofyourchoice.
Tochange,enter:
#4321 08 4digits 3beeps #
ProgAccess. Index Newpassword Conrmation Outprog.
INPUT TIME
Allowstheusertoentertheprotectedlocationtodisarmtheboard
throughthekeyboard,withouttriggeringthealarm.
Thefactorydefaultis00 seconds(inputtimedisabled).Tosetthe
inputtime,enter:
#4321 09 2digits #
ProgAccess. Index Time(Up00to99s) Outprog.
OUTPUT TIME
Allows the user to leave the protected location after arming the
board,withouttriggeringthealarm.Thefactorydefaultis00 seconds
(exittimedisabled).Tosettheexittime,type:
#4321 10 2digits #
ProgAccess. Index Time(Up00to99s) Outprog.
SECTOR SHUTDOWN
After4 consecutiveviolationsof a single sector, it is automatically
abrogated,avoidingtriggering the alarm, ensuring battery life and
avoidinganyannoyancewithneighbors.Tore-integratethebypassed
sectorsintothesystem,disassembleandresetthepanel.Toenable /
disablethisfunction,enter:
#4321 11 1 # #
ProgAccess. Index LEDSector1on=Enable
LEDSector1o=Disable
Conrm Outprog.
WARNING
Afteritisautomaticallycancel,thesectorwillbedisabledandwill
notdetectviolationsuntilthesystemisdisarmedandreset.
AUTOMATIC ARM
Thisfunctionenables/disablesandsetsthetimeforself-timerinthe
absenceof on-sitemovement.The board willautomaticallyarmall
sectors.Thefactorydefaultsettingis00 minutes(automaticarming
disabled).Tosetthetimeautoarm,type:
#4321 12 2digits # #
ProgAccess. Index Time(Up00to99minutes) Conrm Outprog.
TELEPHONE DIALING
Callsregisteredphonesincaseofalarmtriggering.
Seethecallcycle:
Tel. Calls 1 ... Tel. 2 ... Tel. 3 ... Tel. 4 ... Tel. 5 ... Tel. 6 ...
Thepanelwillsoundasirensoundfor1 minute viatelephone,
alertingtheuserabouttheviolation.
Tointerruptthecycle,disarmtheboardthroughtheremotecontrol
or keyboard. For security reasons, remote key locking does not
interruptdialing.
BEEPS ON THE ARM AND DISARM
Indicates,throughthesiren,thearminganddisarmingoftheboard.
Toenable/disablethisfunction,type:
#4321 13 1 # #
ProgAccess. Index LEDSector1on=Enablebeeps
LEDSetor1o=Disablebeeps
Conrm Outprog.
USING VOICE MODULE
This function enables / disables the use of the voice module. The
voicemoduleplaysvoicemessageonthephoneintheeventofan
alarmbeingtriggered.Toenable/disablethisfunction,enter:
#4321 14 1 # #
ProgAccess. Index LEDSector1on=Enable
LEDSector1o=Disable
Conrm Outprog.
WARNING
Thisfunctionmustonlybeenabledifavoiceisinstalled.
REGISTERING CONTROLS
Followthissequencetoregistercontrols:
#4321 15 Select1ormoresectors(1to4) #
ProgAccess. Index LEDSectoron=Sectorenabledforcommand
LEDSectoro=Sectordisabledforcommand
Conrm
LEDS
correspondentes
aossetorespiscam
Keepthecontrol
buttonpressed
3beeps
Release
the
control
Button
#
Conrmation Outprog.
Iftheboardemits 1 long beep (error),itmeansthattheprocedure
didnot runcorrectlyor thememory isalreadyfull. Thisprocedure
mustbecarriedoutinamaximumof15 seconds.Afterthistime,the
boardwillautomaticallyterminatetheprocessbysendinganerror
beep.Ifyouareregisteringabuttonthatwasalreadyrecorded,the
sectorsofthisbuttonwillbeupdatedtothecurrentlyselectedones.
REGISTERING WIRELESS SENSORS
Performthisoperationneartheboardtopreventinterferencefrom
damagingtherecordingprocess.Followthesequence:
#4321 16 Select1sector(1to4) #
ProgAccess. Index LEDSectoron=Enablesectorforsensor
The factory default is LED sector 1 on
Conrm
LEDofsector
corresponding
keepashing
3beeps #
Conrmation Outprog.
Iftheboardissues1 long beep (error),itmeansthattheproceduredid
notruncorrectlyorthememoryisalreadyfull.Thisproceduremustbe
carriedoutinamaximumof15 seconds.Afterthistime,theboardwill
automaticallyterminatetheprocess,emittinganerrorbeep.
DELETING WIRELESS SENSORS CONTROLS
Toremoveallregisteredrecords,type:
#4321 17 #
ProgAccess. Index Outprog.
Todeleteallregisteredwirelesssensors,type:
#4321 18 #
ProgAccess. Index Outprog.
WARNING
Becarefulnottoaccessindexes17and18accidentally,asyou
accesstheseindexes,wirelesscontrolsandsensorswillbe
automaticallydeleted.
DIALING IN PULSE / RING (DTMF)
Toselectthedialingmode,type:
#4321 19 1 # #
ProgAccess. Index LEDSector1on=dialring(DTMF)
LEDSector1o=pulsedial
Conrm Outprog.
DIALING TESTS
Itallowstotesttheregisteredphones,withouttriggeringthesiren.
a)CheckiftheLine LEDiso(outofprogrammingmode).
b)PresstheF key andthememorynumbertobechecked(1 to 6).
Note that in this case, the number 0 (zero) is not entered.
c)TheLine LED willbeonwhiletheboardisdialing.
d)Verifyiftheregisteredtelephonereceivedthecallandifthesiren
soundwasheardoverthetelephone.Otherwise,theregistrationis
incorrectandmustberedone.
FAILURE BEEPS WHEN ARMING
Emits3beepsonthesirenwhentryingtoarmtheboardwithsome
opensector.Inthiscase,theboardwillnotbearmed.Toenable/
disablethisfunction,enter:
P04433-Rev.1

PPA CODIGUS 4D PLUS Specifications

General

Brand	PPA
Model	CODIGUS 4D PLUS
Category	Security System
Language	English

Summary

Accessing Programming Mode

Registering and Deleting Phones

Local Calls Phone Registration

Procedure for registering local phone numbers, up to 22 digits each.

Deleting Telephone Numbers

Methods to delete registered phone numbers one by one.

Password Management

Installer Password Change

Procedure to change the installer password.

User Password Change

Procedure to change the user password.

Time Settings and Functions

Input Time Configuration

Set time to disarm without triggering alarm.

Output Time Configuration

Set time to leave protected location after arming.

Sector Shutdown

Auto-disable sectors after multiple violations.

Automatic Arm Configuration

Enable/set time for self-arming in absence of movement.

Device and Dialing Operations

Voice Module Usage

Enable/disable voice module for alarm messages.

Registering Controls

Registering Wireless Sensors

Deleting Wireless Devices

Dialing Mode Selection

Dialing Test Procedure

Failure Beeps on Arming

Advanced Functions and Settings

Failure Beeps on Arming Configuration

Panic Via Remote Control

Immediate Panic Function

Siren Time Configuration

Low Battery Warning

Input A/D Arm and Disarm

Call Answering Settings

Output LED/PGM Configuration

Timed Sectors Setup

Intelligent Sectors Configuration

Persistent or Interrupt Phone Call

Board Arming and Disarming

Aborting Sectors

Sector Violation (Alarm Clock)

Violation Memory

Board LEDs Signal System Conditions