PreciseFit DC0001-N - Operation Instructions; Operation Safety and Guidelines; Wheel Lubrication Guide; Routine Maintenance

OP
E RATION
I
N
STRU
CTIONS
OPERATION
CAUTION:
Vehicle braking and
stability
may
be
affected
with the
addition
of
an accessory or an
attachment.
Be
aware of changing
conditions
on
slopes.
1 .
Refer
to the
vehicle owner's
manual
for
instructions
on safe
operation
on slopes.
2.
For best
handling
and
traction, distribute
the
weight of the
load evenly
in
the cart.
3.
Always
test
to
make sure
your
tractor
has
adequate
towing and
braking capabilities
whenever
hauling
a
substantial amount
of
weight
in
your
cart. Use extra
caution
when
operating
on
slopes.
3.
CAUTION:
Do
not
exceed
the
towing
capacity
of
the
vehicle.
Follow any
weight limitations
listed
in the
veh icle operator's
man ual.
4.To dump
material from
the
cart,
remove the
tailgate
by
Iifting
it
straight
up and
out
from
between
the
guides.
Release the
spring
latch
on the
tongue by
pulling
the latch tock
lever
forward, away
from
the
cart.
The
cart bed
will
then
tilt backwards
to empty
its
contents.
After
emptying,
pull
the
front of the bed
down
toward
the
cart
tongue until
the
latch
snaps
into
place.
Replace the
tailgate
if
desired.
5.
The maximum
towing speed
for
this cart
is
10
m
ph.
GAUTION:
To
avoid
possible
injury,
before
releasing
the
latch
be sure that no one
is
near the
ca
rt.
MAINTENANCE
1. At the beginning of
each season,
lubricate
the latch, the
latch
pivot
bolt, and the area
of
the
axle
where the drawbar
tongue
pivots
with light machine oil.
2. Grease or
oil
the wheel bearings
periodically.
Use automotive
wheel
bearing
type
g
rease
o
r 20 weig
ht
oil
.
3.
Keep tires
filled to the
recommended tire
pressure
of 30
psi.
HOW
TO
LUBRIGATE
YOUR
WHEELS
To
enhance the
function and
longevity of
your
wheels,
periodically
Iubricate
the beanings.
To lubricate, follow these
steps:
Take
off the
wheels.
If
you
have a
grease
gun
at
hand,
insert
the
nozzle into the
hub and
inject
3-4 drops
of
bearing
type
greasel
ubricant
onto
the
opposite bearing.
Make
sure
the wheel
is
standing
upright and
the
nozzle
reaches
deep enough so
the
drops
are
squeezed
on
the
orbit
of the opposite
bearing.
lf
you
have no
grease
gun
at
hand,
you
can
also lu
bricate
you
r wheels
with a brush.
Dip
a
brush
in
bearing
type
g
rease
lu
bricaht,
thread the brush
into the
hub till
it reaches
the
bearing
on
the opposite
end
of the
hub.
Trace
the orbit of
the bearing
to spread
lubricant
evenly.
To
ensure
the bearing
is
soaked
with
enough
lubricant,
repeat 5-6
times.
Follow
the same steps
to iuOficate
the
bearing on
the other
end
of
the
hub on the
wheel.
Reattach the
wheels.
2.
4.
5.
INSIDE
VIEW OF
OPPOSITE
BEARING
INSIDE VIEW OF
1.