Page 13K&(%$*4.8"4,7%R'*#$"&8#J%/7*,#*%4,77%PSTTTSTQQSUVWV1ITEM 69727
F=K6EBF6E;XCX6I=E@C>D=@>E6>=><6
<.*4a"83%,89%K"77"83%K'*7
Y=I>@>Zb EC%XI6!6>E%F6I@C;F%
@>c;IB%KICD%K@I6-
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel. Do not smoke.
1. Clean the Fuel Cap and the area around it.
2. Unscrew and remove the Fuel Cap.
3. Remove the Strainer and remove any dirt
and debris. Then replace the Strainer.
>&$*-%%L&%8&$%'#*%3,#&7"8*%4&8$,"8"83%5&(*%$.,8%
Pfk%*$.,8&7%h6Pfi1%%L&%8&$%'#*%6TU%*$.,8&71%%=99%2'*7%
#$,+"7"l*(%$&%$.*%3,#&7"8*%&(%$.*%Y,((,8$H%"#%!C@L1
>&$*-%%L&%8&$%'#*%3,#&7"8*%$.,$%.,#%+**8%#$&(*9%"8%,%
5*$,7%2'*7%4&8$,"8*(%&(%,%9"($H%2'*7%4&8$,"8*(1%%@$%4,8%
4,'#*%/,($"47*#%$&%*8$*(%$.*%4,(+'(*$&(J%,22*4$"83%
*83"8*%/*(2&(5,84*%,890&(%4,'#"83%9,5,3*1
4. If needed, fill the Fuel Tank to about 1 inch under
the fill neck of the Fuel Tank with 87 octane or
higher unleaded gasoline that has been treated
with a fuel stabilizer additive. Follow fuel stabilizer
manufacturer’s recommendations for use.
5. Then replace the Fuel Cap.
6. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
683"8*%C"7%<.,83*
<=;E@C>b Oil is very hot during operation and can
cause burns. Wait for engine to cool before changing oil.
1. Make sure the engine is stopped and is level.
2. Close the Fuel Valve.
3. Place a drain pan (not included) underneath
the crankcase’s drain plug.
4. Remove the drain plug and, if possible,
tilt the crankcase slightly to help drain
the oil out. Recycle used oil.
5. Replace the drain plug and tighten it.
6. Clean the top of the Dipstick and the area around it.
Remove the Dipstick by turning it counterclockwise,
and wipe it off with a clean, lint free rag.
7.
Full level
Full level
Add the appropriate type of oil until the oil level is at
the full level. SAE 10W-30 oil is recommended for
general use.
The SAE Viscosity Grade chart shows other
viscosities to use in different average temperatures.
PfYSef
ef
UYSef
-20 0 20 40 60 80 100°F
F=6%!"#4&#"$H%Z(,9*#
=M*(,3*%&'$9&&(%$*5/*(,$'(*
8. Thread the dipstick back in clockwise.
>CE@<6-%%L&%8&$%('8%$.*%*83"8*%)"$.%$&&%7"$$7*%&"71
Engine%)"77%8&$%#$,($%)"$.%7&)%&(%8&%*83"8*%&"71
To Next Page
Loading...
Need help?
General
