Page 17G+)&*(><$#>'C&Q=("*#+$"F&AC('"(&>'CC&RSTTTSTUUSVWXW9ITEM 63962
8.G763876!Y4Y7E.614/5.1/67/./-7
-<(>`#$%&'$,&G#CC#$%&G=(C
Z.E/1/:h 64&YE7D7/6&87E14!8&
1/i!E3&GE45&G1E7L
Fill the fuel tank in a well-ventilated area
away from ignition sources. If the engine is
hot from use, shut the engine off and wait
for it to cool before adding fuel.
Do not smoke.
1. Clean the Fuel Cap and the area around it.
2. Unscrew and remove the Fuel Cap.
/+*(L I+&$+*&="(&%'"+C#$(&>+$*'#$#$%&@+)(&*<'$&
Rel&(*<'$+C&^7Re_9&&I+&$+*&="(&7TV&(*<'$+C9
/+*(L&&I+&$+*&="(&%'"+C#$(&*<'*&<'"&?(($&"*+)(,&#$&'&
@(*'C&J=(C&>+$*'#$()&+)&'&,#)*B&J=(C&>+$*'#$()9&&1*&>'$&
>'="(&A')*#>C("&*+&($*()&*<(&>')?=)(*+)F&(JJ(>*#$%&
($%#$(&A()J+)@'$>(&'$,M+)&>'="#$%&,'@'%(9
3. If needed, fill the Fuel Tank to about 1 inch
under the fill neck with 87 octane or higher
unleaded gasoline that has been treated with
a fuel stabilizer additive. Follow fuel stabilizer
manufacturer’s recommendations for use.
4. Replace the Fuel Cap.
5. Wipe up any spilled fuel and allow excess
to evaporate before starting engine.
To prevent FIRE, do not start the engine
while the smell of fuel hangs in the air.
7$%#$(&4#C&-<'$%(
-.!614/h Oil is very hot during operation and can
cause burns. Wait for engine to cool before changing oil.
1. Make sure the engine is stopped and is level.
2. Close the Fuel Valve.
3. Place a drain pan (not included) underneath
the crankcase’s drain plug.
4. Remove the drain plug and, if possible,
tilt the crankcase slightly to help drain
the oil out. Recycle used oil.
5. Replace the drain plug and tighten it.
6. Clean the top of the Dipstick and the area around it.
Remove the Dipstick by threading it counterclockwise,
and wipe it off with a clean lint free rag.
7.
Full level
Full level
Add the appropriate type of oil until the
oil level is at the full level. SAE 10W-30
oil is recommended for general use.
/+*(L Do not thread the dipstick in
when checking the oil level.
The SAE Viscosity Grade chart shows other
viscosities to use in different average temperatures.
ReZSce
ce
VZSce
-20 0 20 40 60 80 100°F
8.7&D#">+"#*B&:)',("
.K()'%(&+=*,++)&*(@A()'*=)(
8. Thread the dipstick back in clockwise.
/461-7L&I+&$+*&)=$&*<(&($%#$(&H#*<&*++&C#**C(&+#C9&&
7$%#$(&H#CC&$+*&"*')*&H#*<&C+H&+)&$+&($%#$(&+#C9
.#)&G#C*()&7C(@($*&5'#$*($'$>(
1. Remove the air filter cover and the air filter elements
and check for dirt. Clean as described below.
2. -C('$#$%L
• For “paper” filter elements:
To prevent injury from dust and debris,
wear ANSI-approved safety goggles,
NIOSH-approved dust mask/respirator, and
heavy-duty work gloves. In a well-ventilated
area away from bystanders, use pressurized
air to blow dust out of the air filter. If this
does not get the filter clean, replace it.
• For foam filter elements:
Wash the element in warm water and
mild detergent several times. Rinse.
Squeeze out excess water and allow it to dry
completely. Soak the filter in lightweight oil
briefly, then squeeze out the excess oil.
3. Install the cleaned filter. Secure the
Air Cleaner Cover before use.
To Next Page
Loading...
