A
x8
D
4x 4
B
x8
D
3x 3
C
x8
C
x6
9
8
6
7
1
2
1
3
6
7
C
C
C
A
D
A
B
D
Installation guide
Item No.:CAB-ET101
Technical Data
Column Number
Maximum Load
Speed
Input Voltage
Lowest Position(with desktop)
Highest Position(with desktop)
Desktop Size
Duty Cycle
Protection Class
Applicable Temperature
Certification Standard
80KG
18mm/s
110V
750mm
1230mm
1200*600*25mm/1400*700*25mm
0~40°C
CE FCC
2
1600*800*25mm
2 minutes on, 18 minutes off
Accessory kit
Note: The drawings below are only for reference and may be slightly different with the object, please in kind prevail. Any tools missing or
installation problems, please contact the customer service freely.
Part list
Installation instruction
ID Part
Qty
ID Part
Qty
ID Part
Qty
STEP1:
Use 4 PCS of Hexagon Socket Button Head Screws(A) to connect “L” Marked Desk
Foot(1) and “L” Marked Desk Leg(2), and use a 4*4 Wrench(D) to fasten.
Similarly, use 4 PCS of Hexagon Socket Button Head Screws (A) to connect “R”
Marked Desk Foot (1) and “R” Marked Desk Leg (3), with arrows in the same
directions, and use a 4*4 Wrench (D) to fasten.
STEP4:
Install mounting plate(6) to “L” element of table leg by four hexagon socket
button head screws (B), then fasten them by 3x3 wrench(D). Use the same
way to install the right mounting plate(7) to the right.
Attention: Marks are in
the same direction
STEP5: STEP6:
Attention: Worksurface is optional
worksurface
Electric phillips
screwdriver
Using the 8pcs cross recessed countersunk head screw(C) to install the
worksurface with the right (6)and left(7) support plate, and tight them by
cross screwdriver or electric pistol drill.
Using the 6pcs cross recessed countersunk head screw (C) to install the control
box(8) and the handset (9) with the worksurface, tight them by cross
screwdriver or electric pistol drill. Pay attention to the installation direction of
the control box and handset, and the connecting line range, should be as what
is shown in the figure.
Attention make sure both parts ：
are heading the same direction
A
x8
M6X16mm
B
x16
M5X10mm
C D
x14
x2
St4.2X20mm
4x4
3x3
6x6
E
x1
1
2
1
3
4
5
6
8
9
7
1 1
1 0
1 2
1 2 3
4 5 6
7 8 9
10 11 12
1+1 1 1
11
1
1
2 1
1 1
6
P u t t w o h e x a g o n j o i n t l e v e r s ( 5 ) t h r o u g h l e f t a n d r i g h t e l e-
m e n t s o f t h e t a b l e l e g t o t w o s i d e d d r i v i n g l e v e r o f m o t o r e l e-
m e n t ( 4 ) , l o c k i t w i t h l o c k i n g f a s t e n e r , a s d i s p l a y e d i n t h e
p h o t o .
5
4 5
1
2
3
Install to card slot position
unscrew the plastic
nut
connect driving
lever
lock the plastic nut
Use 8 PCS of Hexagon Socket Button Head Screws(B) to connect Motor
Module(4) to “L” Marked Leg Module and "R" Marked Leg Module respectively,
and use a 3*3 Wrench(D) to fasten them. Motor Module (4) needs to be installed
with Arrow label upward, do not misplace.
x8
3x 3
B
D
！
Insert driving lever to card slot
position on desk leg
shorter part
Attention: while there's
no access to install the
drive link, try to use the
6x6 wrench(E) fine
turning table legs to make
hexagon direction same
as motor element
shorter part
B
D
B
Motor Module(4) needs to be installed at
the "Shorter Part" side, with Arrow label
upward, do not misplace.
STEP3:
STEP2:
To Next Page
Need help?
General
