How to reduce vibration during extraction in Primus FS 6-16?
Excessive vibration during extraction in your Primus Washer can be due to several factors. Ensure that the bolts of the cabinet and reinforcements are properly tightened. Check the installation of the vibration switch and reinstall if necessary. If the issue persists, the suspension may be damaged.
Why is my Primus FS 6-16 Washer machine not filling with water?
If your Primus Washer machine is not filling with water, or the filling time seems excessively long, here are a few things to check: * Ensure that the inlet taps are fully open. * Verify that the water pressure is adequate by inspecting your supply installation. * Look for any kinks or obstructions in the inlet hose that might be blocking the water flow. * Inspect the inlet valve filter for blockages; close the water inlet before cleaning the filter. * The inlet valve may be damaged and require replacement.
Why is my Primus FS 6-16 leaking?
If your Primus Washer machine is leaking, check the following: * Ensure that all hose clamps are properly tightened. * Inspect the hoses for any damage and replace them if necessary. * Examine the sealing for damage and replace if needed. * Make sure the supply and drain hoses are correctly connected.
How to fix a Primus FS 6-16 Washer with a display that's not lighting up?
If the display on your Primus Washer machine is not lighting up when you switch on the power, consider the following potential causes: * Ensure there is external power supplied to the machine; verify the external tension. * Check if the emergency button is activated; deactivate it if it is. * Confirm that the power connector is properly connected on the board; connect it if it is not. * Verify the power connector is not inversely connected; check the wiring and connect it correctly. * Inspect the fuse on the PWR board; if the transformer is deformed, replace the PWR board. If the transformer is okay, change the fuse. * Ensure the input connector is connected; connect it if it is disconnected. * Check if the EPROM containing the software is correctly implemented; insert the c...
Why is the heating time too long on my Primus FS 6-16 Washer?
If the heating time is too long in your Primus Washer, the heating elements may be defective and need to be changed. Examine the wiring for damage or incorrect connections; replace or repair as needed. Calcium sediments on the heating elements can also cause this issue, so clean or replace the heating elements.
Why is my Primus FS 6-16 Washer not behaving as expected?
If your Primus Washer is not behaving as expected, ensure the correct machine type is selected in the S-submenu, as selecting the wrong type can activate incorrect outputs. Also, check the suspension system; if it's not working and the shock absorbers are cold, consider changing the shock absorbers or springs.
What does it mean when my Primus Washer displays dashes and a countdown?
If you see dashes displayed on your Primus Washer and a counter counting down on the lower display, this indicates a wait state. This is likely caused by a power interruption or a safety sequence at the end of the process. Wait until the counter reaches 0.
Why is there a lack of steam in my Primus Washer?
If there is a lack of steam in your Primus Washer machine, consider the following potential causes: * A leak in the steam system; repair the leakage. * Too much condensation in the steam system; remove the condensate. * Too many machines on one supply; disconnect other machines or increase steam capacity.
What to do if the keyboard buttons on my Primus Washer are not responding?
If your Primus Washer isn't responding when you press the keyboard buttons, check if the input connector A is well connected and inspect the wiring between the input connector and the keyswitch. If the START button is not functional, set the Key switch to Run mode. If the SET button is not functional, ensure the key switch is in Program mode. If no button is functional and the key switch is in the right position, check if the connector K of the keyboard is well connected.
Why does the coindrop accept coins but not start the Primus FS 6-16 Washer?
If the coindrop on your Primus Washer is accepting coins but not starting the washer, it could be due to these reasons: * Ensure the start button is pressed after the amount is flashing on '00'. * Verify that the correct amount of money has been inserted into the coindrop. * Make sure the door is completely and properly closed.
Crucial safety instructions for installation, operation, and maintenance to prevent injury or damage.
Details machine dimensions, packing dimensions, drum sizes, and weight for different models.
Covers electrical supply requirements, voltage deviations, power input, and input protection ratings.
Outlines washing parameters, water inlet types, pressure, temperature, and steam connection.
Specifies acceptable ambient working conditions, humidity, and maximum noise output.
Guides on initial inspection, proper storage, and positioning requirements for safe installation.
Instructions for positioning the machine correctly and ensuring it is level.
Instructions on removing transport safety features before operation.
Detailed steps for connecting the machine to the electrical supply, including safety devices.
Covers connecting water supplies, steam, and liquid soap dosing systems.
Steps to take before initial operation after installation.
Outlines daily, three-monthly, and six-monthly checks and cleaning tasks.
Instructions for adjusting door seals, vibration switch, and replacing belts.
Guidance on cleaning water filters, checking bolt tightness, and fuse information.
Explains how the machine displays errors and how to interpret diagnostic messages.
Provides a list of common problems, their causes, and step-by-step solutions.
Lists part numbers and descriptions for recommended spare parts.
Steps to safely disconnect the machine from power, water, and steam.
Guidelines for material sorting and disposal when decommissioning the machine.
To Next Page
General
