Why doesn't the water stay in my Primus FS 6-16?
If the water does not stay in the Primus Washer machine, it could be due to: * The drain valve not closing properly; check the wiring to the drain valve. * Leakage of the rubber piece between the tub and drain valve; replace the rubber piece.
How to reduce vibration during extraction in Primus FS 6-16?
Excessive vibration during extraction in your Primus Washer can be due to several factors. Ensure that the bolts of the cabinet and reinforcements are properly tightened. Check the installation of the vibration switch and reinstall if necessary. If the issue persists, the suspension may be damaged.
Why does the coindrop accept coins but not start the Primus FS 6-16 Washer?
If the coindrop on your Primus Washer is accepting coins but not starting the washer, it could be due to these reasons: * Ensure the start button is pressed after the amount is flashing on '00'. * Verify that the correct amount of money has been inserted into the coindrop. * Make sure the door is completely and properly closed.
What causes a Primus Washer not to spin?
If your Primus Washer will not spin, first check the program for any faults. Inspect the wiring for damage and replace as needed. If the V-belts are broken, replace them. The motor itself could be broken, requiring repair or replacement. Lastly, the frequency converter might be damaged and need repair or replacement.
How to fix a door seal leak on a Primus FS 6-16?
If there's a door seal leakage in your Primus Washer, the door rubber seal might be damaged and needs to be changed. Another possible cause is insufficient door pressure, which can be resolved by removing spacers from behind the hinges.
Why is my Primus FS 6-16 Washer not behaving as expected?
If your Primus Washer is not behaving as expected, ensure the correct machine type is selected in the S-submenu, as selecting the wrong type can activate incorrect outputs. Also, check the suspension system; if it's not working and the shock absorbers are cold, consider changing the shock absorbers or springs.
How to fix a Primus FS 6-16 Washer with a display that's not lighting up?
If the display on your Primus Washer machine is not lighting up when you switch on the power, consider the following potential causes: * Ensure there is external power supplied to the machine; verify the external tension. * Check if the emergency button is activated; deactivate it if it is. * Confirm that the power connector is properly connected on the board; connect it if it is not. * Verify the power connector is not inversely connected; check the wiring and connect it correctly. * Inspect the fuse on the PWR board; if the transformer is deformed, replace the PWR board. If the transformer is okay, change the fuse. * Ensure the input connector is connected; connect it if it is disconnected. * Check if the EPROM containing the software is correctly implemented; insert the c...
Why is my Primus Washer not starting when I press the start button?
If your Primus Washer machine is not starting when you press the start button, check these items: * Ensure the key switch is set to 'Run' mode, not 'Program' mode. * Make sure the correct amount of coins has been inserted; the start button should be pressed when '00' is flashing on the lower display. * Verify that the door is fully and properly closed.
What to do if the Primus Washer door fails to open?
If your Primus Washer machine door fails to open, consider the following: * If a fault has occurred, wait until the counter reaches ‘0’. * If the power is off, the safety mechanism may be engaged; wait until the safety device is inactive. * If the power is off and the door is jammed after a few minutes, you can manually override the door. Ensure the machine has stopped spinning and there is no hot water remaining in the tub before attempting this.
Why is my Primus FS 6-16 leaking?
If your Primus Washer machine is leaking, check the following: * Ensure that all hose clamps are properly tightened. * Inspect the hoses for any damage and replace them if necessary. * Examine the sealing for damage and replace if needed. * Make sure the supply and drain hoses are correctly connected.
Crucial safety instructions for installation, operation, and maintenance to prevent injury or damage.
Details machine dimensions, packing dimensions, drum sizes, and weight for different models.
Covers electrical supply requirements, voltage deviations, power input, and input protection ratings.
Outlines washing parameters, water inlet types, pressure, temperature, and steam connection.
Specifies acceptable ambient working conditions, humidity, and maximum noise output.
Guides on initial inspection, proper storage, and positioning requirements for safe installation.
Instructions for positioning the machine correctly and ensuring it is level.
Instructions on removing transport safety features before operation.
Detailed steps for connecting the machine to the electrical supply, including safety devices.
Covers connecting water supplies, steam, and liquid soap dosing systems.
Steps to take before initial operation after installation.
Outlines daily, three-monthly, and six-monthly checks and cleaning tasks.
Instructions for adjusting door seals, vibration switch, and replacing belts.
Guidance on cleaning water filters, checking bolt tightness, and fuse information.
Explains how the machine displays errors and how to interpret diagnostic messages.
Provides a list of common problems, their causes, and step-by-step solutions.
Lists part numbers and descriptions for recommended spare parts.
Steps to safely disconnect the machine from power, water, and steam.
Guidelines for material sorting and disposal when decommissioning the machine.
To Next Page
General
