Pro1 IAQ T731W User Manual

T731W(O)
Installation Manual
Pro1 Technologies
Toll Free : 888-776-1427
Web: www.pro1iaq.com
Hours of Operation: M-F 9AM - 6PM Eastern
Thermostat Application Guide
Description
Gas or Oil Heat
Electric Furnace
Heat Pump (No Aux. or Emergency Heat)
Heat Pump (With Electric Aux.)
Multi-Stage Systems
Heat Only Systems - Floor or Wall Furnace
Cool Only Systems
Millivolt
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Power Type
Battery Power
Hardwire (Common Wire)
Hardwire (Common Wire) with
Battery Backup
Table of Contents
Installation Tips
Thermostat Quick Reference
Base Module Mounting Tips
Wiring
Technician Setup
Establishing Communication
Network Specications
Specications
Page
A trained, experienced
technician must install this
product.
Carefully read these
instructions. You could damage
this product or cause a
hazardous condition if you fail
to follow these instructions.
Una version en español de este
manual se puede descargar en
la pagina web de la compañia.
Rev. 2010
Mount Thermostat
Align the 4 tabs on the subbase
with corresponding slots on the
back of the thermostat, then push
gently until the thermostat snaps
in place.
Battery Installation
Battery installation is
optional if thermostat is
hardwired (R and C terminal
connected to 24V power).
Important:
High quality alkaline batteries are recommended.
Rechargeable batteries or low quality batteries
do not guarantee a 1-year life span.
Insert 2 AA
Alkaline batteries
(included). High
quality alkaline
batteries are
recommended.
Installation Tips
2
4-5
8-11
12-16
1
2-3
Installation Tips Thermostat Quick Reference
Getting to know your thermostat
3
4
Subbase Installation
The thermostat should be installed approximately 4 to 5 feet above the
oor. Select an area with average temperature and good air circulation.
• Close to hot or cold air ducts
• That are in direct sunlight
• With an outside wall behind
the thermostat
• In areas that do not require
conditioning
• Where there are dead spots
or drafts
(in corners or behind doors)
• Where there might be
concealed chimneys or
pipes
Wall Locations
Vertical Mount
Horizontal Mount
For vertical mount put one screw on the top
and one screw on the bottom.
For horizontal mount put one screw on the
left and one screw on the right.
All of our products are mercury free.
However, if the product you are
replacing contains mercury, dispose of
it properly. Your local waste
management authority can give you
instructions on recycling and proper
disposal.
Pick an installation location that is easy for
the user to access. The temperature of the
location should be representative of the
building.
Installation Tip
Mercury Notice
Do not install
thermostat in locations:
Failure to disconnect the power before
beginning to install this product can
cause electrical shock or equipment
damage.
Installation Tip:
Electrical Hazard
U.S. Registered Trademark. Patents pending
Copyright 2020 All Rights Reserved.
Heat Pump (With Gas Aux.)
Emergency Heat
Conventional Single Stage Furnace
Geothermal
High, Medium and Low Fan Speed
No
No
Yes
Yes
19
Located on the back of thermostat.
P.O. Box 3377
Springeld, MO 65808-3377
Glow in the Dark Light Button
Setpoint Buttons
LCD
System Button
Fan Button
R
17-18
20
6-7
Occupancy Sensor
(Occupancy Model Only)

Pro1 IAQ T731W Specifications

Temperature

temperature display range	41˚F to 95˚F (5˚C to 35˚C)
temperature control range	44˚F to 90˚F (7˚C to 32˚C)
heating swing adjustment	0.2˚ to 2.0˚
cooling swing adjustment	0.2˚ to 2.0˚

Power

thermostat power source	18 to 30 VAC, NEC Class II, 50/60 Hz
thermostat battery power	2 AA Alkaline batteries
base module power source	18 to 30 VAC, NEC Class II, 50/60 Hz

Operating Environment

thermostat operating ambient temperature	32˚F to +105˚F (0˚C to +41˚C)
base module operating ambient temperature	32˚F to +150˚F (0˚C to +65˚C)
operating humidity	90% non-condensing maximum

Load Rating

thermostat load rating per terminal	1 amp
thermostat maximum load rating all terminals combined	1.5 amp
base module load rating per terminal	1 amp
base module maximum load rating all terminals combined	1.5 amp

Dimensions and Frequency

dimensions of thermostat	4.7”W x 4.4”H x 1.1”D
frequency	916 MHz

Summary

Installation Tips

Wall Locations

Select an area with average temperature and good air circulation, 4-5 feet above floor.

Subbase Installation

Electrical Hazard Warning

Failure to disconnect power before installation can cause shock or equipment damage.

Mount Thermostat

Battery Installation

Instructions for installing AA alkaline batteries for thermostat power.

Getting to Know Your Thermostat

Thermostat Quick Reference

Overview of the thermostat's LCD display and key buttons.

Thermostat Quick Reference Details

Important Battery Warning

Details the consequences of not replacing low batteries.

Base Module PTAC Installation

Base Module Mounting Tips

Tips for mounting the base module to optimize wireless range.

Wiring Instructions

Wiring Notes & Tips

Electrical Hazard Warning (Wiring)

Disconnect power before wiring to prevent shock or equipment damage.

Wiring Compliance Warning

All wiring must conform to Class II circuits per NEC Code.

PTAC Wiring Note

Technician Setup

Technician Setup Menu Navigation

Instructions for entering, navigating, and exiting the technician setup menu.

Important Tech Setting Notes

Cooling Swing Setting

Heating Swing Setting

Technician Setup Options

Fan Operation Setting

Selects thermostat or system control for fan operation during heat call.

Fan Speeds Setting

Compressor Short Cycle Protection

Protects compressor from short cycling with a 5-minute delay.

Heating Setpoint Limit

Sets a maximum heat setpoint temperature to prevent overheating.

Cooling Setpoint Limit

Sets a minimum cool setpoint temperature to prevent overcooling.

Display Light Setting

Enter Network Pairing

Initiates the pairing process to connect the thermostat to the base module.

Heat Pump Configuration

Configures the thermostat for heat pump systems or non-heat pump systems.

Technician Setup (Occupancy Models)

Local Occupancy Sensor

Enables or disables the occupancy sensor for automatic temperature setbacks.

Duration of Occupancy

Occupied Cool Setting

Occupied Heat Setting

Unoccupied Cool Setting

Unoccupied Heat Setting

Occupancy Sensitivity Setting

Establishing Communication

Establishing Communication between Thermostat & Base Module

Details on how the thermostat and base module communicate wirelessly.

How To Pair

Step-by-step instructions for pairing the thermostat and base module.

How To Unpair

Base Module LED Information