EasyManua.ls Logo

PROMARKS DC-650 - User Manual

PROMARKS DC-650
58 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
DC-650
Double Chamber Vacuum Packaging
Machine
Operation Manual
Version 6.9.1
PROMARKS INC
1915 E. Acacia Street, Ontario, CA91761, U.S.A
TEL : 1-909-923-3888
FAX : 1-909-923-3588
http://www.promarksvac.com
S/N: QC SIGNATURE:

Table of Contents

Questions and Answers

  • T
    Terry EvansAug 14, 2025
    What to do if PROMARKS DC-650 has no or improper sealing?
    • J
      Jordan RoyAug 14, 2025
      If your PROMARKS Kitchen Appliances unit isn't sealing properly, several factors could be at play. It might be due to a broken or loose sealing wire, in which case you should replace or tighten it. Insufficient pressure could be the issue; if the pressure bar is damaged, replace it. Other potential culprits include a damaged sealing transformer, Teflon tape, or silicone rubber, all of which would need replacing. Make sure that you adjust to the proper sealing and cooling time, and if the sealing pressure is too low, replace the pressure bag.
  • A
    Amanda RamosAug 17, 2025
    Why is there insufficient vacuum in the bag with PROMARKS DC-650?
    • H
      Henry Baldwin MDAug 17, 2025
      If you're experiencing insufficient vacuum in the bag with your PROMARKS Kitchen Appliances, it could be due to several reasons. The bag might be leaking, in which case you should replace it. If sharp corners on the wrapped product are puncturing the bag, replace the bag with a thicker one. Also, ensure that you are using the correct bag size; if the bag is too large, replace it with a smaller one.
  • D
    darlene20Aug 21, 2025
    What to do if sealing area of PROMARKS DC-650 Kitchen Appliances has burnt marks or bubbles?
    • K
      Kyle MortonAug 21, 2025
      If the sealing area of your PROMARKS Kitchen Appliances has burnt marks or bubbles, it's likely due to contamination or excessive heat. Clean the sealing area to remove any oil, meat juice, or dirt. Also, the sealing time (temperature) might be too long (high), so adjust it to be shorter (lower).
  • C
    Christopher FergusonAug 25, 2025
    Why is there insufficient vacuum in the chamber of PROMARKS Kitchen Appliances?
    • J
      Jeremy ArroyoAug 25, 2025
      If you notice insufficient vacuum in the chamber of your PROMARKS Kitchen Appliances, there are a couple of things to check. First, the oil level in the vacuum pump might be low, so fill it if necessary. Second, the lid silicone rubber could be damaged, in this case, stop machine immediately, alter the power connection and reconnect to correct ones, and replace the silicone rubber.
  • T
    Tiffany HowellAug 27, 2025
    How to fix vacuum bag that is easily pulled apart by hand with PROMARKS Kitchen Appliances?
    • M
      mooresaraAug 27, 2025
      If the vacuum bag is easily pulled apart by hand after sealing with your PROMARKS Kitchen Appliances, it indicates that the sealing time (temperature) is too short (low). To fix this, adjust the sealing time (temperature) to be longer (higher).
  • K
    Kyle BoothAug 31, 2025
    Why vacuum pump does not run on PROMARKS Kitchen Appliances?
    • A
      Annette MendozaAug 31, 2025
      If the vacuum pump on your PROMARKS Kitchen Appliances isn't running, the power supply might not be corresponding with the power demand indicated on the back of machine. Reconnect to the correct power source.
  • B
    blairanaSep 3, 2025
    What to do if control panel is under normal function, but vacuum pump does not start on PROMARKS Kitchen Appliances?
    • M
      Mr. David Weaver PhDSep 3, 2025
      If the control panel of your PROMARKS Kitchen Appliances is functioning normally but the vacuum pump doesn't start, the KM1, QM1, MCB1, MCB2 protectors might be disconnected. Check each part and turn on the switch; reconnect if necessary.
  • Y
    Yvette ReyesSep 6, 2025
    What to do if lid does not close on PROMARKS DC-650?
    • C
      Christopher ThomasSep 6, 2025
      If the lid of your PROMARKS Kitchen Appliances isn't closing, it could be due to a damaged vacuum valve or a disconnected/damaged limit switch. Replace the vacuum valve. Reconnect or replace the limit switch.
  • S
    Stephen MillerSep 10, 2025
    What to do if lid does not open on PROMARKS Kitchen Appliances?
    • T
      Travis SchmidtSep 10, 2025
      If the lid of your PROMARKS Kitchen Appliances isn't opening, the vacuum valve might be damaged. Replace it.

PROMARKS DC-650 Specifications

General IconGeneral
ModelDC-650
CategoryKitchen Appliances
TypeDigital Kitchen Scale
Power Source2 x AAA batteries
Auto-OffYes
Tare FunctionYes
MaterialStainless Steel
DisplayLCD
Maximum Capacity650 grams
Precision0.1 grams
Units of MeasurementGrams, Ounces

Related product manuals