1 YEAR LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers.
These warranties give specific legal rights. Except where prohibited by local law, the law of the State
of Washington governs all warranties and all exclusions and limitations of warranties and remedies.
There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship
under normal use and service. A defective product may be returned for a free replacement within 90
days from the date of purchase, provided that product is returned to place of purchase immediately
after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE
TOOL® will replace at no charge any parts which our examination shall disclose to be defective and
under warranty. These warranties shall be valid only when a sales receipt showing the date of
purchase accompanies the defective product or defective part(s) being returned. For part(s) after 90
days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables
which must be replaced under normal use and service. These warranties shall not apply to any
product or part which is used for a purpose for which it is not designed, or which has been repaired or
altered in any way so as to affect adversely its performance or reliability, nor shall these warranties
apply to any product or part which has been subject to misuse, neglect, accident or wear and tear
incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume
any liability in connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE
TOOL® makes no express or implied warranties of any kind with respect to its products. In particular,
PERFORMANCE TOOL® makes no implied warranty of merchantability and no implied warranty of
fitness for any particular purpose, except that for goods purchased primarily for personal, family or
household use and not for commercial or business use, PERFORMANCE TOOL® makes an implied
warranty of merchantability (and, if otherwise applicable, an implied warranty of fitness for a particular
purpose), but only for the particular qualities or characteristics, and for the duration, expressly
warranted above. The laws on limitation of implied warranties may differ from state to state, so the
above limitations may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages
resulting from or in any manner related to any product, or to the design, use, or any inability to use
the product. The sole and exclusive remedy for a defective product or part shall be the repair, or
replacement thereof as provided above. The laws on limitation of remedies or on consequential,
incidental or special damages may vary from state to state, so the above limitations may not apply in
all cases.
© Copyright 2019 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
OWNER'S MANUAL
WARNING: READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS AND
WARNINGS BEFORE OPERATING THIS TOOL. FAILURE TO DO SO MAY
RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE AND WILL
VOID WARRANTY.
1,000 LB. ENGINE STAND
Item Number W41025
1 BEFORE APPLYING LOAD TO STAND, LOCK MOUNTING PLATE WITH
LOCK PIN. (See part #6 on parts drawing.)
2. Attach rear of engine block to mounting head securely according to vehicle
manufacturer's specifications.
3. Assure load is centered and secured to mounting plate before removing
lifting device.
1. Visual inspection shall be made before each use of the stands, checking for
cracks, cracked welds and missing and/or damaged parts. Any stand that
appears to be damaged in any way shall be removed from service
immediately.
2. BECAUSE OF THE POTENTIAL HAZARDS ASSOCIATED WITH THE
MISUSE OF EQUIPMENT OF THIS TYPE, NO MODIFICATIONS SHALL BE
MADE TO THE PRODUCT.
3. Replace worn or damaged parts with Performance Tool replacement parts.
Be sure that only qualified personnel perform repairs.
OPERATION
MAINTENANCE & INSPECTION
To Next Page
Need help?
General