Pulsar ACCOLADE 2 LRF XP50 PRO - Built-In Laser Rangefinder; PiP Function; Stream Vision; Firmware Update

12
Built-In Laser Rangender
The binoculars are equipped with a built-in rangender(17), allowing you to
measure distance to objects up to 1000m away.

•
Turn on the device, set up image according to section Powering On and Image
Setting.
•
Press theUP (2)orbutton on remote control - rangending reticle
appears; in the top right corner of the display dashes of distance values with
unit of measurement appear , i.e. the rangender enters the stand-by
mode.
•
If PiP mode is activated, the aiming reticle disappears upon activation of the rangender and in the PiP
window remains active.
•
Point the rangending reticle at an object and press theUP (2)button.
•
In the top right corner of the display you will see distance in meters (or yards - depending on settings).
Note:if the rangender is idle longer than for 4 seconds, it turns off automatically.
Operation in SCAN mode:
•
To measure distance in scanning mode, hold down theUP (2)orbutton on remote control for
longer than two seconds. Measurement readings will be changing in real time as you point the binoculars at
different objects. MessageSCANappears in the top right corner.
•
To exitSCANmode, pressUP (2)orbutton again.
•
If measurement fails, dashes will appear on the display.
•
In 4 seconds of inactivity (no measurement is taken) the rangender turns off, the rangending reticle with
readings disappears from the display.
Notes:
•
To select a rangending reticle, please see the Reticle Typesubsection.
•
To select a unit of measurement (meters or yards) go to the Units of Measuresubsection.
Peculiarities of operation:
•
Accuracy of measurement and maximum range depend on the reection ratio of the target surface, the angle
at which the emitting beam falls on the target surface and environmental conditions. Reectivity is also
affected by surface texture, color, size and shape of the target. A shiny or brightly colored surface is normally
more reective than a dark surface.
•
Measuring range to a small sized target is more difcult than to a large sized target.
•
Accuracy of measurement can also be affected by light conditions, fog, haze, rain, snow etc. Ranging
performance can degrade in bright conditions or when ranging towards the sun.
Display O Function
The Display Off function deactivates transmission of image to the display by minimizing its brightness. This
prevents accidental disclosure. The device keeps running.
•
When the device is on, hold down thebutton. Display goes out,
messageappears.
•
To activate the display, press briey thebutton.
•
When you press and hold thebutton, the display shows the message“Display
Off”with a countdown. Pressing & holding the button down for the duration of the
countdown will power the device off completely.
SCAN
125
m
PiP Function
PiP (“Picture in Picture”) allows you to see a
zoomed image simultaneously with the main
image in a dedicated window.
•
Enabling/disabling the PiP function is carried
out in the main menu (see section PiP Mode).
•
Change zoom ratio in the PiP window with a
short press of theDOWN (5)button.
•
The zoomed image is displayed in a dedicated
window, while the image in the rest of the
screen is displayed at base magnication (2.5x).
•
When PiP is turned on, you can operate
the discrete and continuous digital zoom.
Magnication will take place only in the
dedicated window.
•
When PiP is turned off, the image magnication
in the main window changes to the value that was set for the PiP window.
Stream Vision
thermal imaging binoculars support Stream Vision technology which allows you to stream
an image from the display of your thermal imager to a smartphone or tablet PC via Wi-Fi in real time mode.

•
Download free of charge Stream Vision App”
https://play.google.com/store/apps/

https://apps.apple.com/us/app/
stream-vision/id1069593770
•
Connect your Pulsar device to your mobile device (smartphone or tablet).
•
Launch Stream Vision and go to section “My Devices”.
•
Select your Pulsar device and press “Check Updates”.
•
Wait for the update to download and install. Pulsar device will reboot and will be ready to operate.
Important:
•
if your Pulsar device is connected to phone, please turn on mobile data transfer (GPRS/3G/4G) to download
update;
•
if your Pulsar device is not connected to your phone but it’s already in the “My Devices” section, you may use
Wi-Fi to download update.

Clickhereto check the latest rmware for your device.
2.5x
5.0x