Need help?Do you have a question about the Pulse PMX1204 and is the answer not in the manual?
Explains the meaning of graphical symbols used in the manual, including warnings and compliance marks.
Explains the phantom power switch function, activating/deactivating power for condenser microphones via XLR.
Details the 1/4" and XLR main output sockets for connecting external processors, amplifiers, or speakers.
Explains 1/4" channel insert jacks for effects and ALT 3-4 unbalanced outputs for routing flexibility.
Details control room outputs for monitoring and the IEC mains inlet with fuse for power connection.
Important safety warning regarding connecting speaker types simultaneously and ensuring correct impedance to prevent amplifier damage.
Details the importance of keeping air vents clear for the power amplifier to maintain correct working temperature.
Details the MIC 1 input, accepting XLR or 1/4" plugs, with phantom power option and connection precautions.
Explains the LINE IN input, accepting 3-pole 1/4" jack plugs for various signal sources like laptops or keyboards.
Information on the LOW CUT button (75 Hz, 18dB/oct) for reducing low-frequency noise like stage rumble.
Explains the GAIN CONTROL for adjusting input signal levels, warning against distortion from too high or hiss from too low gain.
Details the three EQ dial controls: HF (above 12kHz), MF (around 2.5kHz), and LF (below 80Hz) for frequency adjustment.
Explains how to use the HF, MF, and LF EQ dials to adjust specific frequency ranges for tone shaping.
Details AUX, FX controls for signal routing and level setting, and the PAN dial for stereo distribution.
Details MUTE, CLIP LED, SOLO button, and INPUT CHANNEL FADER for individual channel signal management.
Explains STEREO AUX RETURNS sockets and AUX SENDS sockets for external signal routing and monitoring.
Details STEREO AUX RETURN SOCKET and BALANCED DIAL for stereo signal input and balance control.
Explains LEVEL button, INPUT TAPE, OUTPUT CD/TAPE sockets for signal level matching and tape routing.
Details the FX FOOT SWITCH socket for connecting a footswitch to mute sound by pressing down.
Details the PHONES socket for connecting headphones to listen to individual channels or the main mix.
Explains the AUX SENDS DIAL for gain control and the SOLO switch for monitoring aux busses separately.
Details the FX DIAL for gain control and the SOLO switch for monitoring FX busses separately.
Details buttons for selecting CD/TAPE, ALT 3-4, and MAIN MIX sources for headphone monitoring.
Explains the CTRL R. & PHONES dial for setting control room output and headphone volume, with safety note.
Details the TAPE TO MAIN switch to route 2-track input to main mix, disabling main mix to tape output link.
Details STEREO AUX RETURNS DIALS and FX DIAL with MAIN MIX/ALT 3-4 switch for signal routing and level.
Explains PFL (Pre Fader Listen) for level setting and SOLO for isolating individual channel monitoring.
Details the MODE SWITCH for selecting PFL/SOLO and the LED DISPLAY for signal and power status.
Details the ALT 3-4 outputs which are unbalanced and carry signals assigned via the mute switch for subgroups.
Explains the MAIN MIX FADERs used to control the overall signal levels from all channels in the mix.
Details the PROGRAM dial for scrolling and selecting effects presets, with display flashing the current preset number.
Explains the integrated 24-BIT MULTI-EFFECTS PROCESSOR producing reverb, chorus, flanger effects, added to dry signals.
Details power requirements and general mixer specifications including output power and mic pre-amps.
Covers audio performance metrics like THD, gain range, and specifications for EQ and FX processor.
Details aux sends/returns, sub groups, phantom power, and input/output assignments for routing flexibility.
Lists channel features such as Peak LEDs, mute, SOLO, PFL, and line input level settings.
Diagrams for balanced XLR connectors and 1/4" TS connectors used with footswitches.
Diagrams for unbalanced 1/4" TS and balanced 1/4" TRS connectors used for various audio signals.
Diagram for wiring 1/4" TRS connectors for headphone connections, indicating left and right signal paths.
General| Type | Analog Mixer |
|---|---|
| Channels | 12 |
| Microphone Inputs | 4 |
| Line Inputs | 8 |
| Phantom Power | Yes |
| Aux Sends | 2 |
| USB Interface | No |
| EQ Bands | 3 |
| Effects | Built-in |
| Outputs | Main Out |
| Power Supply | External |
To Next Page
