This document is an installation and user guide for the Pureline Prime Plus Pump, specifically the PL1700 Series models. It provides comprehensive information for the installation, operation, maintenance, and troubleshooting of the pool pump.
Function Description:
The Pureline Prime Plus Pump is designed for use in permanently installed swimming pools, and potentially hot tubs and spas if marked accordingly. Its primary function is to circulate water within the pool or spa system, facilitating filtration and maintaining water quality. The pump creates suction to draw water from the pool/spa, pushes it through a filter, and then returns it to the pool/spa.
Important Technical Specifications:
The manual includes an "Electrical Guidance for 60Hz Single phase motors" table, which details various electrical specifications based on the pump's rated power (KW and HP). This table is crucial for proper electrical installation and includes:
- Rated Power: From 0.37 KW (0.5 HP) to 1.88 KW (2.5 HP).
- Voltage: 115V and 230V options for each power rating.
- Circuit Breaker Amps: Ranges from 15A to 30A for 115V and 10A to 20A for 230V.
- Branch Fusetron Amps: Ranges from 15A to 30A for 115V and 6.25A to 20A for 230V.
- Recommended Wire Size (0-50'): Specifies appropriate wire gauges (No. 14, No. 12, No. 10) for different power and voltage configurations.
The pump is designed for outdoor use but requires protection for electrical components from weather. It is not submersible. The motor shaft is made of stainless steel grade 304, and mechanical seals are made from carborundum and graphite for durability and low noise. All components are molded from corrosion-proof reinforced thermoplastic.
Usage Features:
- Large 2" Plumbing Ports: Facilitates efficient water flow and easier installation.
- Voltage Switch: Allows for easy switching between 115V and 230V wiring, providing flexibility for different electrical setups.
- Transparent Strainer Basket Cover: Enables users to visually inspect the strainer basket, indicating when cleaning is necessary without needing to open the pump.
- Easy-to-Remove Strainer Basket Cover: Designed for convenient access for cleaning the strainer basket.
- Drain Plug: Included for easy pump winterization, allowing for complete drainage of water to prevent freezing damage.
- Priming: The pump can prime itself if placed below water level. For installations above water level, detailed instructions are provided, including filling the strainer housing with water, opening air relief valves, and ensuring all suction and discharge valves are open. The manual emphasizes the importance of proper priming to avoid running the pump dry, which can damage seals and void the warranty.
- Safety Features: The pump is equipped with an automatic thermal overload protector that shuts off the motor if the power supply drops below a certain point, preventing damage from heat buildup. It will automatically restart once the motor cools.
- Plumbing Best Practices: The guide recommends using larger plumbing on the suction side (2" or 2.5") and a minimum of 12" of straight pipe into the suction port to improve priming and extend pump life. It advises against using 90-degree elbows within 12" of the suction or discharge ports, suggesting two 45-degree fittings instead. Check valves are recommended on the suction side to help maintain prime after the pump shuts off, with specific placement guidelines based on plumbing size.
- Electrical Installation: Emphasizes that all electrical installation must be performed by a licensed electrician and conform to local and national electrical codes, including grounding and bonding requirements. It provides clear wiring diagrams for both 115V and 230V configurations for single-speed pumps.
Maintenance Features:
- Regular Strainer Basket Cleaning: Users are instructed to clean the strainer basket regularly and inspect the strainer cover gasket, replacing it if necessary.
- Self-Lubricating Motor Bearings and Shaft Seals: The pump does not require lubrication for these components.
- Motor Care: Users are advised to keep the motor clean and ensure air vents are free from obstruction to prevent damage. It explicitly states not to hose off the motor with water.
- Shaft Seal Replacement: Occasionally, shaft seals may need replacement, and users are advised to use genuine seal assembly kits.
- Winterization: Detailed steps are provided for winterizing the pump, including draining water, removing the drain plug and strainer cover, disconnecting the pump, and storing it in a dry area. It warns against using compressed air for purging and recommends propylene glycol as antifreeze.
- Troubleshooting Guide: The manual includes a comprehensive troubleshooting section covering common issues such as the motor not starting, motor shutting off, motor humming but not starting, pump not priming, low flow, and noisy pump. It offers solutions ranging from checking electrical connections and cleaning debris to contacting qualified professionals for more complex problems.
- Warranty: The product comes with a one-year warranty from the date of purchase, covering defects in materials and workmanship. The warranty outlines conditions for repair, replacement, or refund, excluding damage due to freezing, negligence, improper installation, use, or care.
Need help?
General
To Next Page
