Step 4
Warranty and complianceSpecifications
Printed Circuit Board Battery
DELTABELL-WE
Self Powered External Sounder
Installation guide
Installation Steps: Step 1
Step 2 Step 3
EN50131-4:2009
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class IV
Slide the PCB module upwards.
The sprung back-tamper arm
can be retracted to allow
removal. This must be done in
order to install the revolving
guides - see step 3.
Place the base on a flat surface
and ensure it is vertical using the
spirit level that is already
installed. Drill and plug in each
of the fixing locations. The
revolving guides will correct any
misalignment. If the Deltabell WE must be mounted on an uneven
surface, it is recommended that a tamper levelling screw is used to
ensure correct back-tamper operation. See step 2.
Place the PCB
module, ensuring that
the arrow is aligned
with the marker (on
the left of the
module).
Expose the terminals
by releasing the latch
on the top of the PCB
module.
Step 5
Fit the lid by sliding its
hinges into place. The lid
can be supported in the
fully open position. To
close the lid, apply a
little force to push the lid
past the holds.
Close the cover, ensure
the tamper is operating
correctly, insert the
25mm long screw
supplied and rotate the
screw cover to a close.
*Lid sold separately
Mounting the Deltabell WE on
an uneven surface may cause
false triggering, through
incorrect operation of the
back-tamper.
A POZI number 2 screw driver
is recommended for adjusting
back tamper screw.
NOTE: This is for wall
mounting only.
Low voltage 2.5V +/-5% at
threshold: 25ºC
Battery D Cell 3.0 volt
11000MAh
Lithium battery
Acoustic output: Tone.
Strobe duration 10mS
Strobe Frequency 1Hz
Sound pressure level 101dBA
Max sound duration 15 mins
Dimensions 290 x 285 x 50 mm
Reverse polarity protected
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current.
Replace only with approved batteries.
To prevent possible damage to
components, any static charge on your
body needs to be eliminated before
touching the inside of the unit. This can
be accomplished by touching some
grounded/earthed metallic conductor
such as a radiator/pipework
immediately before replacing batteries.
Insert the guides as shown.
Make sure that the guides ‘B’
are aligned with the tabs to
the right (this is so the PCB
module slides in)
Turn each guide until they
line up with the drilled holes,
while referencing the spirit
level for the correct
alignment, and fix the base
firmly to the wall.
Please note, if the Deltabell WE is installed on an uneven surface, it
is recommended that you do not tighten up the wall screws until after
the module is installed (step 4)
Learning the DELTABELL-WE onto the Control Panel
When you are ready to learn the device to the
control panel receiving equipment, and when
the equipment is in the learn mode (see the
Control Panel Programming Manual) follow the
procedure below.
1. Make sure the battery is installed correctly
2. Press and hold the Learn button until the
3 LEDs start cycling through the different
colours, then release.
3. The device is correctly learnt when the
green LED flashes.
WARRANTY: This product is sold subject to our standard
warranty against defects in workmanship for a period of two
years. Please note: In positions where the Deltabell WE
casing is subjected to high levels of U.V. sunlight, there may
be risk of case colour fading, this is not covered by the
warranty. In the interest of continuing improvement of quality,
customer care and design, Pyronix Ltd reserve the right to
amend specifications without giving prior notice.
Pyronix Ltd, Braithwell Way, Hellaby, Rotherham,
South Yorkshire, S66 8QY
Customer support:
+44(0)845 6434 999 (local rate)
or +44(0)1709 535225
Hours: Mon to Fri, 8.00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com
The three coloured LEDs give a
visual indication of the signal
strength.
Green indicates good signal strength
and is a good location to install.
Red indicates poor signal
strength and the device should not
be installed in that position.
If no LED illuminates then the device
is completely out of range.
The blue LED will illuminate when the
device is activated.
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
Tamper
levelling
screw
AC/DC
BATTERY
SOUNDER
TAMPER
LEARN
BAT
+
-
LED3 LED2 LED1
Comfort LED
Enable/Disable
link
Learn button
Optional
auxillary 12
volt PSU input
PLEASE
NOTE:
The auxillary
12V PSU input
is not polarity
conscious
Battery
Sounder
Tamper
Red LED
Blue LED
Green LED
Strobe
Comfort LEDs
RINS1433-2
Tamper switch
For electrical products
sold within the European
Community. At the end
of the electrical products
life, it should not be
disposed of with
household waste. Please
recycle where facilities
exist. Check with your
Local Authority or retailer
for recycling advice in
your country.
When disposing of the
product, the battery
must be removed and
disposed of separately in
accordance with the
local regulations
Please see the Enforcer 32-WE user,
programming and quick set up manuals for
further information
To Next Page
Need help?
General
