Qazqa Cool Fan 52 - User Manual

Questions and Answers

E
Evelyn WilsonAug 5, 2025
What to do if my Qazqa Fan will not start?
- A
  annetteallisonAug 5, 2025
  If your Qazqa Fan won't start, there are several potential causes: 1. A blown fuse or circuit breaker. Check both the main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan. Inspect the line wire connections to the fan. 3. The speed controller may not be in the correct position. Verify the speed controller's position.
K
Kelly FlemingAug 15, 2025
Why is my Qazqa Cool 52 so noisy?
- L
  Luke LucasAug 15, 2025
  If your Qazqa Fan is making excessive noise, consider these possible causes and solutions: 1. The top canopy might be touching the ceiling. Lower the upper canopy to ensure a minimum clearance of 3 mm from the ceiling. 2. Loose fan blade screws. Re-tighten all screws on the fan blades, but be careful not to over-tighten them. 3. The ceiling fan might not be securely attached to the ceiling. Re-tighten all screws in the hanging bracket or plate. 4. An incorrect speed controller may be in use. Change the controller to the one supplied with the fan.
J
Jose ProctorAug 25, 2025
How to fix a Qazqa Cool 52 Fan that wobbles?
- M
  Mrs. Kelsey DorseyAug 25, 2025
  If your Qazqa Fan wobbles, here are a couple of things to check: 1. Fan blades may not be horizontal to the ceiling. Measure from the ceiling to the tip of each blade. Rotate the fan and check that all blades are at an equal height from the ceiling. Adjustments can be made by applying slight pressure up or down on the blade holders. Ensure all screws are securely fastened. 2. Blade screws might be loose. Make sure all screws are securely fastened.

Summary

Installation of the Ceiling Fan

Disconnect for Maintenance and Cleaning

This document provides an instruction manual for the Cool Fan 52, a ceiling fan model with product numbers 92648, 92649, 92650, 92651, and 92652.

Function Description:

The Cool Fan 52 is a ceiling fan designed for indoor use. Its primary function is to circulate air, providing cooling in summer and distributing warm air in winter. It also features an integrated light. The fan is operated via a remote control.

Important Technical Specifications:

Model Numbers: 92648, 92649, 92650, 92651, 92652
Power Supply: 220-240 V, 50 Hz
Rated Wattage: 60 W
Bulb Rating: E14, 2x40W Max (bulbs not included)
Light Type: 2xE14, MAX40W
Protection Class: I
IP Number: IPX0
Ambient Operating Temperature: 25 °C
Minimum Installation Height: Blades must be more than 2.3 m above the floor.
Power Supply Wire Requirement: 1.5 sq mm wire
Maximum Fan Flow Rate (F): 120.30 m³/min
Fan Power Input (P): 42.4 W
Service Value (SV): 2.84 (m³/min)/W
Standby Power Consumption (PSB): 0.23 W
Seasonal Electricity Consumption (Q): 13.83 kWh/a
Fan Sound Power Level (LWA): 44.7 dB(A)
Maximum Air Velocity (C): 1.78 m/seg

Usage Features:

Remote Control Operation: The fan is controlled by a remote, allowing users to adjust fan speed and turn the light on/off.
Adjustable Fan Speeds: The remote control offers multiple speed settings: low, medium, and high, in addition to an OFF setting for the fan.
Light Control: A dedicated button on the remote turns the light ON/OFF.
Reversible Slide Switch (Seasonal Operation):
- Left/Up (Summer Mode): Makes the air movement directly from the ceiling for cooling.
- Right/Down (Winter Mode): Circulates warm air generated by a heater to the floor. It is crucial to stop the fan blades by turning off the fan before pushing the reversible slide switch.
Safety Precautions during Operation:
- Do not place your arm or any other object in the path of the blades when the fan is operating.
- Maintain a minimum distance between the lamp and any inflammable material (curtains, wall, etc.).

Installation Process:

Install the mounting bracket using screws as shown in Fig. 1.
Remove the two screws from the rectangular cover on the motor housing and remove the cover (Fig. 2).
Insert the blades through the slots around the motor (Fig. 3).
Align each blade with the three holes and secure it with three screws through the opening. Tighten all blade screws evenly and ensure the rectangular cover is secured by screws (Fig. 4).
Make sure the wiring connection is done correctly using quick plugs. Consult a qualified electrician if unsure.
- Black + Brown wire: "L" (Live)
- Blue wire: "N" (Neutral)
- Green & yellow wire: Earth wire (must be longer than Live and Neutral wires).
Hang the fan and assemble the mounting bracket with the motor set using four side screws (Fig. 6).
Insert the lens into the receiver and connect the supply wires of the receiver (Fig. 7).
Install the bulb (not included) (Fig. 8).
Install the glass (Fig. 9).
The fan installation is now complete (Fig. 10).
- A wiring diagram is provided, showing connections for Yellow/Green (Ground), Blue (Neutral), Brown (Live), and Black (Motor/Light).
- If the fan or light kit is partially pre-assembled, some assembly steps can be skipped.

Maintenance Features:

Disconnect from Mains: Always disconnect the power from the electrical supply before conducting any cleaning or maintenance work.
Cool-Down Period: Wait until the lamp cools down before handling.
Cleaning:
- Do not use a wet sponge to clean the appliance.
- Avoid abrasive products, solvents, detergents, or any other liquid to clean the fan or lamp.
- Ensure the power is off when cleaning the fan.
- Do not clean the motor, switch housing, or other electrical parts of the fan with water to prevent short circuits.
Troubleshooting (Wobble Problem):
- Dynamic Blade Balancing Kit: If wobble persists after initial checks, a dynamic balancing kit can be used.
- Procedure for Balancing:
  1. Turn the fan on to high speed to identify the greatest wobble.
  2. Turn off the fan. Place the balance clip halfway between the blade holder and the rear edge of one blade.
  3. Turn the fan on to check for improvement or worsening of wobble.
  4. Repeat by moving the clip to other blades to find the most improved blade.
  5. Move the clip inward and outward on the improved blade to find the position that gives the most improvement.
  6. Remove the clip and install a balancing weight to the top of the blade along the centerline near the identified point.
  7. Caution: Stay clear of blades if the clip is not secured to prevent injury.

General Safety Instructions:

Read the instruction manual thoroughly and save it for future reference.
Ensure electrical specifications are compatible with your installation.
Unauthorized use or technical modifications can be dangerous.
Suitable for children aged 8 and above, and persons with reduced capabilities, under supervision and understanding of hazards.
Children should not play with the appliance and cleaning/maintenance should not be done by children without supervision.
Means for disconnection must be incorporated in fixed wiring according to wiring rules.
Never install in moist or wet rooms.
Be careful near rotating blades.
All poles disconnection with contact separation providing full disconnection under overvoltage category III conditions must be incorporated in fixed wiring.
Before accessing terminals, all supply circuits must be disconnected.

Environmental Protection:

Electrical products must not be disposed of with domestic waste.
Take them to a communal collecting point for environmentally friendly disposal according to local regulations.
Packaging material is recyclable; dispose of it in an environmentally friendly manner.