QOLSYS IQ PANEL 2 User Manual

IQ PANEL 2 QUICK GUIDE
Remove the back plate
WALL MOUNT
Press the buttons on the
bottom to release the back
plate from the panel face
Plug in the power supply
(1) and then clip the wire
to the retainer clip (2)
Secure the back plate to the wall,
then loop the hang strap over the
strain relief hook (1) Run the
antenna through the hole (2)
Place the panel onto the top of the
back plate (1) and hinge downward
until it snaps in place. Take care as
you route the antenna into the wall (2)
Plug in the power supply (1)
and then clip the wire to the
retainer clip (2) then into the
strain relief hook (3)
Replace the back cover Connect the table stand to
the holes on the upper back.
CREATE
ACCOUNT
Settings Advanced
(default installer
password is 1111)
Swipe down to access settings tray
Connect power supply
WARNING! Use 5.5v Power Supply ONLY
Press and hold the power
button on the right side of
the panel for 3 seconds to
power up
TRY THE
MOBILE
TECH APP
System
Tests Cell Test
RUN A
CELL TEST
ACCESS ADVANCED SETTINGS
Wi-Fi
CHOOSE
YOUR
NETWORK
CONNECT
WI-FI
Upgrade
Software
UPGRADE
USING
NETWORK
Check for
updates
CHECK FOR
UPDATES
INSTALL
DEVICES
Installation Devices
Security
Sensors
Auto Learn
Sensor
Tamper or
trip sensor
Customize
as desired*
Add New
Touch
“Add New”
ADD SECURITY SENSORS
ADD Z-WAVE DEVICES
Z-Wave
Devices
Add
Device
Touch
“PAIR” (both
on panel and
on the device)
PAIR
Add New
Touch
“Add New”
Customize
as desired
*If pairing devices with encryption, be sure to
select “S-Line” as the “Source” of the signals
Security Signaling Residential Fire Alarm & Security
Equipment, UL Listed
Conforms to ANSI/UL Standards
Conforms to ANSI/UL Std. S985. 1023. & 1635
Certified to ULC Sub. C1023 & ULC Std. S545
Doc#: IQP2-QG-12-16 Rev Date: 12/08/16
Qolsys Inc. proprietary. Reproduction without permission is not permitted.
techsupport@qolsys.com (855) 476-5797
1
2 3 4
5 6
7
8
11
OPTIONAL MOUNTING: TABLE STAND (INCLUDED IN BOX)
9
10

QOLSYS IQ PANEL 2 Specifications

General

Display Size	7-inch
Resolution	1280 x 800
Operating System	Android
Processor	Qualcomm Snapdragon
Connectivity	Wi-Fi, Bluetooth
Camera	5 MP
Microphone	Yes
Speaker	Yes
Battery Backup	Yes
Touch Technology	Capacitive
Siren	85 dB
Wireless Connectivity	Wi-Fi, Z-Wave
Cellular Connectivity	LTE
Supported Security Protocols	128-bit encryption
Compatibility	Compatible with most smart home devices

Summary

Wall Mount Installation

Release Back Plate

Press buttons on the bottom to release the back plate from the panel face.

Secure Back Plate to Wall

Attach back plate to wall, loop hang strap over strain relief hook, and run antenna through hole.

Connect Power Supply

Plug in the power supply and clip the wire to the retainer clip.

Mount Panel to Back Plate

Place panel onto the back plate and hinge downward until it snaps in place.

Optional Table Stand Mounting

Remove Back Plate

Detach the back plate from the panel.

Connect Power and Antenna

Plug in power supply, clip wire to retainer hook, and route antenna.

Replace Back Cover

Reattach the back cover after connecting power and antenna.

Attach Table Stand

Connect the table stand to the designated holes on the upper back.

Device Setup and Configuration

Access Settings Tray

Swipe down to access the system settings tray.

Perform Cell Test

Run a cellular network test to verify connectivity.

Connect Wi-Fi

Connect the device to a Wi-Fi network.

Check for Updates

Check for and install software updates.

Install Devices

Install compatible devices with the system.

Add Security Sensors

Add security sensors to enhance system protection.

Add Z-Wave Devices

Integrate Z-Wave devices into the smart home system.