Quantum LHQM User Manual

MODEL LHQM
EXIT/UNIT COMBINATION
US Patent No. 5,526,251; 5,646,502; 6,142,648; D379,373; 5,611,163; D484,272; D473,672
Canadian Patent No. 80,141 & 2,180,495
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY
OR SIGNIFICANT PROPERTY DAMAGE – For your protection, read and follow these warnings and instructions carefully before
installing or maintaining this equipment. These instructions do not attempt to cover all installation and maintenance situations. If you do
not understand these instructions or additional information is required, contact Lithonia Lighting or your local Lithonia Lighting distributor.
WARNING: RISK OF ELECTRIC SHOCK – NEVER CONNECT TO, DISCONNECT FROM OR SERVICE WHILE EQUIPMENT IS
ENERGIZED.
WARNING: RISK OF FIRE – Lamps are hot. Keep combustibles material away from hot parts. Observe lamp manufacturer’s
warnings, recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.
WARNING: DO NOT USE ABRASIVE MATERIALS, OR OTHER SOLVENTS. USE OF THESE SUBSTANCES MAY DAMAGE
FIXTURE, WHICH MAY RESULT IN PERSONAL INJURY.
WARNING: RISK OF PERSONAL INJURY – This product may have sharp edges. Wear gloves to prevent cuts or abrasions when
removing from carton, handling, installing and maintaining this product. (WHERE APPLICABLE)
• Before wiring to power supply, turn off electricity at fuse or circuit breaker.
• Disconnect A.C. power and unplug battery before servicing.
• Consult your local building code for approved wiring and installation.
• Do not use outdoors.
• Do not let power supply cord touch hot surfaces.
• Do not mount near gas or electric heater.
• Do not install a damaged fixture.
• This product must be installed in accordance with the applicable installation codes and ordinances.
• Proper grounding is required to ensure personal safety. (WHERE APPLICABLE)
• All service shall be performed by qualified service personnel. This product must be installed and maintained in accordance with the
applicable installation codes by a person familiar with the construction and operation of the product and the hazards involved.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
• Do not use this equipment for other than intended use.
• Halogen cycle lamps operate at high temperatures. Do not store or place flammable materials near lamp.
• Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or eyes, flush acid with fresh
water and contact a physician immediately.
CAUTION: Halogen cycle lamp(s) may be used in this fixture. To avoid shattering, do not operate lamp in excess of rated voltage.
Protect lamp against abrasions and scratches and against liquids when lamp is operating. Dispose of lamps with care. Halogen lamps operate
at high temperatures. Do not store or place flammable materials near lamps.
SAVE THESE INSTRUCTIONS

Quantum LHQM Specifications

General

Brand	Quantum
Model	LHQM
Category	Lighting Equipment
Language	English

Summary

Important Safety Safeguards

General Safety Warnings

Covers risks of death, serious injury, fire, electric shock, and property damage during installation and use.

Installation and Maintenance Precautions

Details safe practices for wiring, mounting, servicing, and operation to prevent hazards.

General Information and Component Removal

Component Removal Instructions

Step-by-step guidance for safely removing the face plate, directional chevrons, back plate, canopy, and lens.

Relocating Lamp Mount Assembly

Instructions for disconnecting, removing, relocating, and reconnecting the lamp mount assembly.

DC Connection Procedure

Procedure for connecting the battery to the lamp board after AC power is supplied.

Top Mount Installation

Connecting Power and Securing Canopy

Details on connecting jumper leads to the j-box and securing the canopy with locking pins.

Routing Wires and Housing Installation

Instructions for dressing leads, routing wires, and snapping the exit housing onto the canopy.

Battery Charging Recommendation

Important note on allowing the battery to charge for 24 hours before initial testing and 168 hours for full charge.

Back Mount Installation

Connecting Power and Securing Back Plate

Instructions for connecting supply leads to the j-box and fastening the back plate to the housing.

Securing Housing to Back Plate

Procedure for snapping the housing onto the back plate after wiring and knockout removal.

End-Mounting Directions

Component Removal for End-Mounting

Steps for removing the back plate, lamp assembly, and orienting face/back plates correctly.

Attaching to Junction Box

Instructions for using top mounting methods to attach the unit to a junction box.

Inspection and Maintenance Procedures

Emergency Lighting Testing

Guidelines for testing emergency lighting systems, including normal operation and test switch procedures.

Component Replacement Guidelines

Procedures for replacing batteries, charger boards, and lamp boards.

Wiring Diagram and Battery Information

Wiring Diagram Overview

Visual representation of electrical connections for various options and notes on wiring.

Important Battery Information

Guidance on battery shelf life, initial charging, and replacement for optimal performance.