Quantum ELM4L User Manual

ELM4L & ELM6L
EMERGENCY LIGHTING UNIT
Installation and wiring …………………..…………......…………………………………… P. 2-3
Testing and maintenance ………...…………………………………………………………P. 4-5
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
!
!
!
!
!
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR
SIGNIFICANT PROPERTY DAMAGE - For your protection, read and follow these warnings and instructions carefully before installing or
maintaining this equipment. These instructions do not attempt to cover all installation and maintenance situations. If you do not understand
these instructions or additional information is required, contact Holophane.
WARNING: RISK OF ELECTRIC SHOCK – NEVER CONNECT TO, DISCONNECT FROM OR SERVICE WHILE EQUIPMENT IS
ENERGIZED.
WARNING: DO NOT USE ABRASIVE MATERIALS OR SOLVENTS. USE OF THESE SUBSTANCES MAY DAMAGE FIXTURE,
WHICH MAY RESULT IN PERSONAL INJURY.
WARNING: RISK OF PERSONAL INJURY – This product may have sharp edges. Wear gloves to prevent cuts or abrasions when removing
from carton, handling, installing and maintaining this product.
WARNING: The battery used in this device may present a risk of fire or chemical burn if mistreated. Temperature range 50°F -104°F (10°C -40°C).
Do not disassemble, heat above 70°C (158°F), or incinerate. Replace battery only as directed on the battery label and page 5 of these instructions.
Use of unauthorized battery voids warranty and UL listing of this product and may present a risk of fire or explosion.
•Disconnect A.C. power before servicing.
•All servicing should be performed by qualified personnel.
•Consult your local building code for approved wiring and installation.
•Do not use outdoors unless used with Acuity Brands accessories appropriate to the application.
•Do not mount near gas or electric heater.
•Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
•Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
AND DELIVER TO OWNER AFTER INSTALLATION
“TEST” button / Status Indicator
Press latches to disengage
housing from mounting plate
Remote test option
NOTE: Product versions that are certified in the CA Title 20 Appliance Efficiency Database are marked
BC on the product label.

Quantum ELM4L Specifications

General

Brand	Quantum
Model	ELM4L
Category	Lighting Equipment
Language	English

Summary

Important Safeguards

General Safety Instructions

Read and follow all safety instructions and warnings carefully before installing or maintaining this equipment.

Electric Shock Warning

Never connect to, disconnect from, or service the equipment while it is energized.

Abrasive Materials Warning

Do not use abrasive materials or solvents, as they may damage the fixture and cause injury.

Personal Injury Warning

This product may have sharp edges; wear gloves when handling to prevent cuts or abrasions.

Battery Handling and Safety

Handle batteries with care to avoid fire or chemical burns; do not disassemble, heat, or incinerate.

Installation and Wiring

Junction Box Mounting

Instructions for mounting the unit using a junction box, including knockout removal and wire connections.

Conduit Surface Mounting

Steps for surface mounting using conduit, including knockout removal and securing the mounting plate.

Final Assembly

Connecting the polarized battery plug and ensuring the housing is securely attached to the mounting plate.

Wiring Diagram

Detailed wiring diagram showing connections for battery, lamps, and CLSR module.

Testing and Maintenance

Testing Procedures

Covers manual testing, self-diagnostics, postponing self-tests, and clearing failure indications.

Battery Information and Status

Provides important battery handling information, status indications, and remote test operation.

Battery Replacement

Step-by-step guide for disconnecting, replacing, and reconnecting the battery.

Lamp Replacement

Instructions for removing the lamp bezel, disconnecting, and replacing the lamp assembly.

Charger Board Replacement

Procedure for releasing, removing, and reconnecting components to the charger board.

CLSR Module Replacement

Steps for replacing the CLSR module, including disconnecting related components.