RAB Lighting FXLED78 - User Manual

FXLED78 INSTALLATION INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable
parts inside.
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com
SLIPFITTER MOUNTING
1. The sliptter mounting ts a 2
3
/8” O.D. Tenon.
Place the sliptter over the Tenon and secure the
xture with the 2 Set Screws on the side of the
sliptter.
2. Remove 2 screws on side of Round Cover Plate.
Remove the Round Cover Plate and adjust the
angle of the xture.
3. Loosen the Locking Bolt and swivel xture to
desired angle.
4. Tighten the Locking Bolt and re-attach Round
Cover Plate.
Tenon
Set
Screws
Round
Cover
Plate
Locking
Bolt
Pivot Bolts
TRUNNION MOUNTING
CAUTION: UL and C-UL listed or CSA certied liquid
tight cord grip suitable for use with three conductor
type STW exible cord shall be used for connection
to a wet location outlet box provided by others.
To adjust the angle of the xture using the trunnion:
1. Loosen the Pivot Bolts & angle locking screw.
2. Adjust xture to desired angle.
3. Tighten Pivot Bolts & angle locking screw.
TROUBLESHOOTING
1. Check that the line voltage at the xture is correct.
Refer to wiring directions.
2. Is the xture grounded properly?
3. Is the photocell, if used, functioning properly?
WIRING
Universal voltage drivers permits operation at 120V to
277VAC, 50 or 60 Hz.
1. Connect the BLACK xture lead to the
(+) LINE supply lead.
2. Connect the WHITE xture lead to the
(-) COMMON supply lead.
3. Connect the bare copper Ground wire from xture
to supply ground.

Summary

Important Installation Prerequisites

Slipfitter Mounting Procedure

Mounting Slipfitter and Adjusting Fixture Angle

Steps for attaching the slipfitter, adjusting the fixture angle using the locking bolt, and re-securing the cover plate.

Trunnion Mounting Procedure

Adjusting Fixture Angle with Trunnion Mount

Instructions for loosening pivot bolts and angle locking screw to adjust the fixture's angle, then tightening them.

Troubleshooting Guide

Checking Line Voltage

Verify that the line voltage at the fixture is correct according to wiring directions.

Checking Fixture Grounding

Ensure that the fixture is properly grounded for safety and functionality.

Verifying Photocell Functionality

Check if the photocell, if installed, is functioning correctly as intended.

Wiring Instructions

Connecting Fixture Leads to Supply

Connect the BLACK fixture lead to the (+) LINE, WHITE to (-) COMMON, and bare copper ground to supply ground.

Guard or Shield Installation

Mounting Wire Guard or Poly Shield

Line up guard or shield with pre-drilled holes and secure with provided screws.

Available Accessories

Accessory Identification

List of available accessories including wire guards, poly shields, and lens/door replacements.

Cleaning and Maintenance

Cleaning Fixture Components

Instructions for cleaning the glass lens and warnings about not opening the fixture or touching LEDs.

Product Performance Data

FXLED78 Cool Specifications

Detailed performance metrics including lumens, watts, efficacy, CRI, and correlated color temperature.

FXLED78 Neutral Specifications

Detailed performance metrics including lumens, watts, efficacy, CRI, and correlated color temperature.

FXLED78 Warm Specifications

Detailed performance metrics including lumens, watts, efficacy, CRI, and correlated color temperature.

RAB Lighting FXLED78 Specifications

General

Model	FXLED78
Category	Lighting Equipment
Wattage	78W
Color Temperature	3000K, 4000K, 5000K
Voltage	120-277V
Housing Material	Die-cast Aluminum
Lens Material	Polycarbonate
IP Rating	IP66
Operating Temperature	-40°C to 50°C
Life Rating	100, 000 hours
Warranty	5 Years
Mounting Type	Yoke
Beam Angle	NEMA Type 7H x 6V