The Radley 8V Cordless Mini Rotary Tool Kit is a versatile handheld power tool designed for various applications, including grinding, sanding, polishing, brushing, and cutting. It is a cordless device, offering freedom of movement and convenience during operation.
Function Description
The rotary tool is primarily used for intricate work, allowing users to perform detailed tasks that require precision. It can be fitted with a variety of accessories, such as grinding bits, sanding bands, polishing wheels, wire brushes, and cut-off wheels, to suit different materials and applications. The tool's motor drives the chosen accessory at a high rotational speed, enabling efficient material removal, shaping, or finishing. Its cordless design, powered by an 8V battery, makes it suitable for use in locations without immediate access to power outlets.
Important Technical Specifications
- Voltage Rating: 8V DC
- Rated Speed: 5,000–25,000 RPM (Revolutions Per Minute)
- Collet Size: 1/8" (3.2 mm)
- Battery: 900mAh Li-ion, Built-in
- Charger Output: 9V 0.5A
- Charging Time: 2-3 hours
- Max Running Time at No Load: 3 hours
- Weight: 0.7 lbs
The tool features a speed control button, allowing users to adjust the rotational speed to match the specific task and material. The LED speed indicator lights provide visual feedback on the selected speed setting. A spindle lock button facilitates easy accessory changes, while the on/off button controls power to the tool. The battery charging light indicates the charging status, and the charging port is used to connect the USB charging cable.
Usage Features
Unpacking and Set-Up:
Before first use, ensure all accessories are present. The kit typically includes 24 accessories and a charger. To change accessories, press the spindle lock button, unscrew the collet nut, and remove the old accessory. Insert the desired accessory, tighten the collet nut, and release the spindle lock. The tool is designed to accept accessories with a 1/8" (3.2 mm) shank. For larger accessories (over 35mm (1.37") in diameter), it is recommended to use accessories specifically fitted to the rotary tool.
Controls:
The tool is turned "ON" by pressing the on/off button. The LED worklight will illuminate, and the tool will start operating at a speed of 5,000 RPM. To turn the tool "OFF," press the on/off button again. The speed can be adjusted using the speed control button. Pressing the plus (+) button increases the speed, while pressing the minus (-) button decreases it. The tool offers a range of speeds from 5,000 RPM (lowest speed) to 25,000 RPM (highest speed), with 5 speed control buttons.
Operation:
For optimal performance and safety, ensure the workpiece is securely clamped down. Select the appropriate speed for the application. For high-precision applications, hold the rotary tool like a pen. For heavy work like cutting or grinding, hold the rotary tool in the palm of your hand. Always gently apply the tip of the accessory to the workpiece. Excessive load on the rotary tool can lead to overheating and motor failure.
Accessories and Their Applications:
- Stone Grinding Bits: Suitable for various kinds of grinding and sharpening applications. Available in a wide range of sizes and shapes (round pointed, flat, etc.). Recommended speed settings vary by material (Soft Wood, Hard Wood, Laminates/Plastics, Steel, Aluminum/Brass, etc., Shell/Stone, Ceramic, Glass).
- Diamond Bits: Made for intricate work on ceramics, wood carvings, jewelry, and scrimshaw. Available in a wide variety of shapes and sizes. Speed settings are also material-dependent.
- Sanding Bands and Paper: Used for shaping wood, smoothing fiberglass, sanding inside curves, and other difficult-to-reach areas.
- Wool Polishing Wheels: Used for bringing metal surfaces to a smooth finish, often with polishing compound.
- Bristle Brush: Ideal for cleaning tools on silverware, jewelry, and antiques.
- Multipurpose Cutter: Ideal for shaping, smoothing, or removing material from especially hard materials.
- HSS Drill Bit: Used to cut wood, plastic, fiberglass, drywall, laminate, aluminum, and vinyl siding.
- Cut-Off Wheel: Ideal for shaping, smoothing, or removing material from especially hard materials.
- Collet: Used to fit a variety of accessories with different shank sizes.
- Sanding Drum: A shank used with sanding bands.
- Screw Mandrel: A shank that screws into wool polishing tips and wheels.
- Mandrel: A small screw-tip mandrel used with cut-off wheels, sanding discs, and buffing discs.
- Wrench: Used to fasten accessories to the mandrels.
Maintenance Features
Cleaning and Storing:
Regularly clean the vents of the rotary tool to prevent foreign matter from entering. After each use, blow air through the rotary tool housing to ensure it is free from dust particles that may build up and cause overheating or motor failure. The enclosure of the rotary tool requires cleaning; do not use solvents but a moist soft cloth only. Never let any liquid get inside the rotary tool. Never immerse any part of the rotary tool into a liquid. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent. Always store the rotary tool indoors.
Accessories:
All accessories can be kept in the plastic accessory container for convenient storage and transport.
Troubleshooting:
- Tool will not turn on:
- Possible Cause: ON/OFF button does not work.
- Remedy: Check that the button is properly engaging the electronic assembly.
- Possible Cause: Battery no power.
- Remedy: Charge the battery with the supplied charger, then turn the tool on after the battery is fully charged.
- Possible Cause: Faulty electronic assembly.
- Remedy: Replace the entire electronic assembly.
- Can not adjust the speed:
- Possible Cause: Speed control button loose or faulty electronic assembly.
- Remedy: Replace the entire electronic assembly.
- Shaft on the rotary tool will not lock:
- Possible Cause: Faulty shaft lock button.
- Remedy: If the shaft rotates even when the shaft lock is pressed, the button will need replacement.
- Tool is overheating:
- Possible Cause: Ventilation slots are covered.
- Remedy: Clean the vents, ensure they are not covered by dust, dirt, etc.
- Possible Cause: Overuse or overpressure onto rotary tool.
- Remedy: During use, make sure to pause occasionally to reduce temperature (especially working at low speed condition). Apply proper pressure when using tool according to its rating.
- Bits or collet no longer tighten/loosen:
- Possible Cause: Collet flexibility, Collet nut worn out, Bits shank worn out.
- Remedy: Replace with new collet, collet nut, or bits.
- Tool makes a squealing and whistling sound:
- Possible Cause: Faulty bearing assembly or fan is broken.
- Remedy: Entire armature and bearing assembly need to be replaced immediately.
Battery and Charger Safety Warnings:
- This charger is not intended for any uses other than charging rechargeable batteries.
- Any other use may result in risk of fire, electric shock, or electrocution.
- Since battery tools do not have to be plugged into an electric outlet, they are always in an operational condition. Be aware of possible hazards when not using the battery tool or when changing accessories.
- Do not place battery tools or batteries near fire or heat. This will reduce the risk of explosion and possibly injury.
- Do not crash, drop, or damage battery. A damaged battery is subject to explosion.
- To avoid damage to the electric plug and cord when disconnecting the charger, be sure to pull by the plug-in, not the cord.
- To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
- A battery can explode or set near a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product near an open flame.
- Do not charge battery till in a damp or wet location. Do not use, store, or charge battery or products in locations where the temperature is less than 50°F or more than 100°F.
- Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention.
Warranty:
The product is guaranteed for a maximum period of 12 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. Warranty excludes consumable parts (e.g., bearings and O-rings).
- 30-Day Money Back Guarantee: Within the first 30 days of purchase, you are allowed to return your product for a full refund.
- 30 Days to 90 Days (3 Months): A defective unit will be replaced with a new one in accordance with the terms of this warranty, due to manufacturing fault.
- 90 Days to 12 Months: Up to 12 months after purchase, we will provide speedy and effective online service.
WARNING: The following actions will result in the warranty becoming void.
- If the tool has been operated on a supply voltage other than that specified on the tool.
- If the tool shows signs of damage or defects caused by or resulting from abuse, accidents, or alterations.
- Failure to perform maintenance as set out within the user manual.
- If the product is disassembled or tampered with in any way.
Need help?
General
To Next Page