EasyManuals Logo

Rainfresh 30T User Manual

Rainfresh 30T
10 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
7
Salt Setting (lbs/cu ft)
Model 6.0 8.0 10.0 12.0 15.0
30T 2.9 3.8 4.8 5.7 7.1
45T 4.2 5.7 7.1 8.5 10.7
60T 5.7 7.6 9.6 11.4 14.2
Table 1 : Refill time (in minutes) for various salt settings (or next whole number)
STEP 7: Manual Regeneration
If screen is locked, press
MENU” for 3 seconds to unlock.
To initiate an immediate regeneration, press the SET/REGEN
button for 3 seconds, an option for Delayed” or Immediate” regeneration will appear. Press the SET/REGEN button
again and Delayed will begin flashing. Now press the down arrow button and Immediate will flash. Press the
SET/REGEN button once and then press the menu button once. Valve will immediately start manual regeneration.
YOUR UNIT IS NOW READY FOR SERVICE
Parameter Option 1 Option 2 Option 3 Option 4 Comments
1 System Language English Spanish French Set to French if desired. Spanish not
enabled
2 Valve Operation Softener Filter Iron
Filter
Leave at default setting
3 Regeneration
Mode
Meter
Delayed
Meter
Override
Calendar
Clock
Meter
Immediate
Leave at default setting
4 Regeneration Time 2:00 AM The unit is factory set to regenerate at 2:00
AM on the day of regeneration. You can
change to another time if desired.
5 Capacity
Calculation
Automatic Manual Automatic (recommended). Change to
manual settings if desired.
6 Resin Volume For 30T unit, set resin volume at 1.0 cu ft
For 45T unit, set resin volume at 1.5 cu ft
For 60C unit, set resin volume at 2.0 cu ft
7 Salt Setting Leave at default setting for maximum efficiency. (Defaults – 30T = 6.0, 45T=9.0, 60C=12)
Set at 15 lb/ft³ for maximum capacity
Note: Capacity = Amount of water that can be softened between regenerations. Capacity reduces
when salt setting is reduced, but salt consumption efficiency increases.
8 Refill Flow Rate 0.7 GPM Leave at default setting
9 Unit Capacity For 30T, default = 20,000 at 6lbs/ft³. Set at 30,000 grains if you chose 15 lbs salt/ft³ in step7
For 45T, default = 30,000 at 9lbs/ft³. Set at 45,000 grains if you chose 15 lbs salt/ft³ in step7
For 60T, default = 40,000 at 12lbs/ft³. Set at 60,000 grains if you chose 15 lbs salt/ft³ in step7
10 Reserve Capacity 75
gal/person
Increase or decrease value as desired
11 Capacity This will be the calculated unit capacity in US Gal. The unit will regenerate only when this much
water has been used.
12 Backwash 05 Increase to 10 if water has lot of dirt or rust
13 Brine / Rinse 50 Increase to 60 if water is more than 15
grains hard
14 Rapid Rinse 5 Increase to 10 if you want a longer rinse
time after regeneration
15 Refill
For REFILL settings based on your chosen salt settings, please refer to Table 1 below
16 Restore Default NO
Leave at default. Change only if you would like
to re-start programming from the beginning

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Rainfresh 30T and is the answer not in the manual?

Rainfresh 30T Specifications

General IconGeneral
BrandRainfresh
Model30T
CategoryWater Dispenser
LanguageEnglish

Related product manuals