RAUMEDIC NeuroSmart logO

Questions and Answers

Y
yatesbriannaAug 18, 2025
What to do if my RAUMEDIC NeuroSmart logO shows 'Battery low'?
- J
  Jessica HillAug 18, 2025
  If the RAUMEDIC Medical Equipment displays a 'Battery low' message, it means the device can operate for approximately 30 more minutes without a power adapter. Connect the adapter to continue operation.
C
Christopher LopezAug 21, 2025
Why can't I carry out zero calibration on my RAUMEDIC NeuroSmart logO Medical Equipment?
- D
  Deborah WilliamsAug 21, 2025
  If the zero calibration fails on your RAUMEDIC Medical Equipment, it might be because the pressure changed by more than 2 mmHg. Ensure the pressure is stable and then repeat the zero balance procedure.
D
Dorothy MartinezAug 23, 2025
What to do if the measured values are constant on RAUMEDIC NeuroSmart logO?
- C
  chaveztylerAug 23, 2025
  If the measured values on your RAUMEDIC Medical Equipment remain constant, it could indicate a defective or improperly connected catheter. Confirm this with OK. Check the pulsation of the pressure signals. If no pulsating pressure signals are displayed even though the catheter/transducer is connected to the patient, it is probably a sensor defect.
M
Melissa RobinsonAug 26, 2025
What happens when the data storage is full on RAUMEDIC NeuroSmart logO Medical Equipment?
- J
  Joseph BlakeAug 26, 2025
  When the data storage of your RAUMEDIC Medical Equipment is almost full, save the data to a PC. Otherwise, the oldest data will be overwritten.
J
Jodi FordAug 27, 2025
Why is the connection with NEUROVENT P-tel interrupted in RAUMEDIC NeuroSmart logO?
- S
  Stephanie HughesAug 27, 2025
  If the connection with the NEUROVENT P-tel is interrupted on your RAUMEDIC Medical Equipment, the NEUROVENT P-tel may be outside the reader's transmission range. Check the reader’s location and correct it if necessary.
V
Victoria WilliamsAug 30, 2025
How to fix 'No connection to NEUROVENT P-tel possible' on RAUMEDIC?
- J
  Jesse PriceAug 30, 2025
  If no connection to the NEUROVENT P-tel is possible with your RAUMEDIC Medical Equipment, check the position of the reader antenna.
W
wphamSep 1, 2025
Why is the amplitude of the measurement signal too low on RAUMEDIC NeuroSmart logO?
- T
  Thomas MillerSep 1, 2025
  If the amplitude of the measurement signal for the oxygen partial pressure is too low on your RAUMEDIC Medical Equipment: * Check the catheter and the oxygen socket. * Check the plug connection and fibre optic cable. Clean the ST socket on the NeuroSmart and ST plug on the catheter.
N
Nicholas StephensSep 3, 2025
How to correct a system time failure on RAUMEDIC Medical Equipment?
- J
  John GonzalezSep 4, 2025
  If there is a system time failure on your RAUMEDIC Medical Equipment, check the date and time and correct them if necessary.
K
kyle12Sep 6, 2025
What to do if the O2 catheter is faulty on RAUMEDIC Medical Equipment?
- R
  raymond17Sep 6, 2025
  If the connected O2 catheter is faulty on your RAUMEDIC Medical Equipment, use another catheter.
C
christophermooreSep 8, 2025
What to do if temperature channel is defective on RAUMEDIC NeuroSmart logO Medical Equipment?
- S
  Sarah ParrishSep 8, 2025
  If the temperature channel is defective or the temperature T2 is outside the measuring range on your RAUMEDIC Medical Equipment, check the cables and catheters or switch off T2.