Raven SCS 4400 - User Manual

104 pages

To Next Page

To Next Page

Loading...

SCS 4000/5000 Series™ Consoles

Installation and Operation Manual

P/N 016-0159-925 Rev F 05/15 E19667

Copyright 2015

Table of Contents

Default Chapter3
- Table of Contents3
- Calibration Reference Sheet7
  - Edit Mode7
- Unit Definitions and Conversions8
  - Unit of Measure Definitions8
  - Unit of Measure Conversions8
Chapter 1 Important Safety Information9
- Safety Information9
  - Hydraulic Safety10
  - Electrical Safety10
Chapter 2 Introduction11
- Introduction11
  - Sprayer & Spreader Control Systems11
- System Components12
- SCS 4000/5000 Series Console Feature Overview13
- Care and Use15
- Technical Specifications15
- Updates16
CAN Networking and CAN Data Menu17
Chapter 3 CAN Networking and CAN Data Menu19
- Detecting CAN Nodes25
- Programming Canbus Nodes26
- CAN Troubleshooting26
  - CAN Node Off-Line Errors26
Chapter 4 Installation29
- Mount the SCS Console30
- Cable and Power Connections30
- Installation29
  - Install the SCS Console29
Chapter 5 Initial Startup & Console Programming35
- Initial Calibration Sequence35
  - Reprogramming Initial Settings39
- Console Programming40
- Self Test Mode42
- Decimal Shift43
Chapter 6 Data Menu45
- Serial Submenu45
- Additional Serial Options46
  - Scs 4000/4070/500046
  - Scs 4400/460046
- Product Submenu47
  - Page49
  - Page51
- Console Submenu53
- CAN Submenu54
- Calibration Summary55
- Data Logger (4400 and 4600 Only)55
  - Setup55
- SCS Alarm Definitions57
Chapter 7 Console Calibration59
- Wheel Drive Speed Sensor60
- Speedometer Drive Speed Sensor61
- Liquid Applications62
- Dual Loop Control Mode Settings65
  - Flow Cal65
  - System (Pressure) Gain66
- Granular Applications66
- Additional Calibration Data68
  - Entering Tank Volume68
  - Zero Out" Display Information68
- Console Calibration59
  - Speed Cal59
Job Setup & Field Testing69
- Liquid Applications69
- Granular Applications71
Chapter 8 Job Setup & Field Testing71
Chapter 10 Testing Extension Cables74
Chapter 9 Troubleshooting75
Testing Extension Cables77
- Speed Sensor Cables77
  - Testing the Speed Sensor Cable77
- Flow Meter/Encoder Cables78
  - Testing the Flow Meter Cable78
Connecting an SCS Console to a Raven Field Computer79
- Firmware Requirements79
  - Operation Guidelines79
- Field Computer Set up80
  - Viper Pro80
  - Envizio Pro or Envizio Pro II80
Chapter 11 Connecting an SCS Console to a Raven Field Computer81
- Cruizer or Cruizer II82
Chapter 12 Flow Meter Maintenance & Adjustment Procedure85
Chapter 13 Ratio Rate Feature87
- Ratio Rate Feature87
Chapter 14 Remote Switch Option89
- Remote Switch Option89
SCS 4000/5000 Series Firmware Update Procedure91
- Using a USB to Serial Adapter91
  - USB to Serial Adapter Preparation91
- Serial Console Updater Utility93
Chapter 15 SCS 4000/5000 Series Firmware Update Procedure93
- Hyperterminal95
Serial Interface & Data String Formats97
- Remote Computer to SCS Console97
  - Rate Change Request97
- SCS 4000/4070/5000 Console to Remote Computer98
- SCS 4400/4600 Console to Remote Computer99
Chapter 16 Serial Interface & Data String Formats99

Questions and Answers

M
milesjackieNov 3, 2025
How to fix Raven Music Mixer CANbus when it cannot read the product node?
- J
  Jimmy WarrenNov 3, 2025
  To address the issue of the CANbus not reading the product node on your Raven Music Mixer, try the following: * Connect the node and reboot the SCS console. * Ensure proper power by connecting the 16 gauge red wire (clean power) and 12 gauge red wire (high current power) from the product node to a 12V DC power source capable of powering all CANbus-connected nodes. * Establish a reliable ground by connecting the 16 gauge white wire (clean ground) and 12 gauge white wire (high current ground) to a quality ground source, preferably the battery's negative terminal. * Confirm that both ends of the CANbus system are correctly terminated; consult the Raven CANbus Installation Manual for details. * Inspect CANbus cable connectors for corrosion, applying dielectric grease to connections ...

Raven SCS 4400 Specifications

General

Channels	4
Inputs	4 XLR/TRS combo
Outputs	2 XLR
EQ	3-band
USB Interface	Yes

Summary

Chapter 1 Important Safety Information

Safety Information

General safety advice for operating the console and following manual instructions.

Hydraulic Safety

Safety precautions and recommendations when working on any hydraulic system.

Electrical Safety

Chapter 3 CAN Networking and CAN Data Menu

CAN Troubleshooting

Chapter 4 Installation

Install the SCS Console

Mount the SCS Console

Cable and Power Connections

Steps for connecting the console's cables and power supply.

Chapter 5 Initial Startup & Console Programming

Initial Calibration Sequence

Step-by-step guide for the initial console setup and calibration.

Chapter 7 Console Calibration

Speed Cal

Procedure for calibrating the console's speed sensor readings.

Wheel Drive Speed Sensor

Detailed steps for calibrating the wheel drive speed sensor.

Speedometer Drive Speed Sensor

Steps for calibrating the speedometer drive speed sensor.

Liquid Applications

Boom Cal

How to calibrate boom widths for accurate application.

Valve Cal

Procedure for programming valve calibration numbers for proper response.

Rate Cal

Setting the target application rate for product application.

Granular Applications

Spreader Constant

Calculating and verifying the spreader constant for granular products.

Product Density

Chapter 8 Job Setup & Field Testing

Chapter 9 Troubleshooting

No display with power ON

Steps to resolve issues when the console shows no display.

Speed display “0.”

Troubleshooting steps for when the speed display shows zero.

Rate inaccurate or unstable

Guidance for diagnosing and correcting inaccurate or unstable rate readings.

Console displays “check CAN nodes or CAN communication”

Steps to resolve CAN communication errors and node connectivity.

Chapter 11 Connecting an SCS Console to a Raven Field Computer

Chapter 12 Flow Meter Maintenance & Adjustment Procedure

Procedure to Recalibrate Flow Meter

Step-by-step guide for recalibrating the flow meter.

Chapter 15 SCS 4000;5000 Series Firmware Update Procedure

Using a USB to Serial Adapter

USB to Serial Adapter Preparation

Serial Console Updater Utility

Guide to using the updater utility for firmware installation.

Hyperterminal

Related product manuals

Preview: Raven SCS 4600

Raven SCS 4000 Series

Preview: Raven SCS 5000 Series

Raven SCS 5000 Series

Raven SCS 700 PGM Series

Preview: Raven MTi