Raymond LVA805A+ - Washing Machine Installation; Installation Location and Preparation; Removing Transportation Locks; Connecting Water Supply

3 / EN
Washing Machine / User’s Manual
2 Installation
RefertothenearestAuthorisedServiceAgentforinstallation
oftheproduct.Tomaketheproductreadyforuse,review
the information in the user manual and make sure that the
electricity,tapwatersupplyandwaterdrainagesystemsare
appropriatebeforecallingtheAuthorizedServiceAgent.Ifthey
arenot,callaqualifiedtechnicianandplumbertohaveany
necessary arrangements carried out.
C
INFORMATIONS
Preparationofthelocationandelectrical,tapwaterandwaste
water installations at the place of installation is under customer’s
responsibility.
Make sure that the water inlet and discharge hoses as well as the
powercablearenotfolded,pinchedorcrushedwhilepushingthe
product into its place after installation or cleaning procedures.
B WARNING
Installationandelectricalconnectionsoftheproductmustbe
carriedoutbytheAuthorizedServiceAgent.Manufacturershallnot
beheldliablefordamagesthatmayarisefromprocedurescarried
outbyunauthorizedpersons.
A WARNING
Priortoinstallation,visuallycheckiftheproducthasanydefectson
it.Ifso,donothaveitinstalled.Damagedproductscauserisksfor
your safety.
2.1 Appropriate installation location
• Placethemachineonarigidfloor.Donotplaceitonalong
pile rug or similar surfaces.
• Totalweightofthewashingmachineandthedryer-with
full load- when they are placed on top of each other
reachestoapprox.180kilograms.Placetheproductona
solid and flat floor that has sufficient load carrying capacity!
• Donotplacetheproductonthepowercable.
• Donotinstalltheproductatplaceswheretemperaturemay
fallbelow0ºC.
• Placetheproductatleast1cmawayfromtheedgesof
other furniture.
2.2 Removing packaging reinforcement
Tiltthemachinebackwardstoremovethepackaging
reinforcement.Removethepackagingreinforcementby
pullingtheribbon.
2.3 Removing the transportation locks
A WARNING
Donotremovethetransportationlocksbeforetakingoutthe
packaging reinforcement.
Removethetransportationsafetyboltsbeforeoperatingthe
washingmachine!Otherwise,theproductwillbedamaged.
Loosenalltheboltswithasuitablespanneruntiltheyrotate
freely(C).Removetransportationsafetyboltsbyturningthem
gently.AttachtheplasticcoverssuppliedintheUserManual
bagintotheholesontherearpanel.(P)
C
INFORMATIONS
Keepthetransportationsafetyboltsinasafeplacetoreusewhen
thewashingmachineneedstobemovedagaininthefuture.
Nevermovetheproductwithoutthetransportationsafetybolts
properly fixed in place!
2.4 Connecting water supply
C
INFORMATIONS
Thewatersupplypressurerequiredtoruntheproductisbetween
1to10bars(0.1–1MPa).Itisnecessarytohave10–80liters
of water flowing from the fully open tap in one minute to have your
machinerunsmoothly.Attachapressurereducingvalveifwater
pressure is higher.
Ifyouaregoingtousethedoublewater-inletproductasasingle
(cold)water-inletunit,youmustinstallthesuppliedstopperto
thehotwatervalvebeforeoperatingtheproduct.(Appliesforthe
productssuppliedwithablindstoppergroup.)
Ifyouwanttousebothwaterinletsoftheproduct,connectthe
hot water hose after removing the stopper and gasket group from
thehotwatervalve.(Appliesfortheproductssuppliedwithablind
stopper group.)
A WARNING
Modelswithasinglewaterinletshouldnotbeconnectedtothe
hotwatertap.Insuchacasethelaundrywillgetdamagedorthe
product will switch to protection mode and will not operate.
Donotuseoldorusedwaterinlethosesonthenewproduct.Itmay
cause stains on your laundry.
1.Connectthespecialhosessuppliedwiththeproducttothe
waterinletsontheproduct.Redhose(left)(max.90ºC)is
forhotwaterinlet,bluehose(right)(max.25ºC)isforcold
water inlet.
A WARNING
Ensure that the cold and hot water connections are made correctly
wheninstallingtheproduct.Otherwise,yourlaundrywillcomeout
hot at the end of the washing process and wear out.
Tightenallhosenutsbyhand.Neveruseawrenchwhen
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points.Ifanyleaksoccur,turnoffthetapandremovethenut.
Retighten the nut carefully after checking the seal. To prevent
waterleakagesanddamagescausedbythem,keepthetaps
closed when the machine is not in use.