RDS Pro Series - User Manual

ARTEMIS PSi QUICK REFERENCE GUIDE
PT NO. S/DC/500
-
10
-
731 : ISSUE 1.00 : 2/7/13 : UK731100.DOC
“
Tramline Bouts”
The Wheel Marks display
a tick when on a tramline
bout and which side is
active.
The Second line shows
the current Tramline Bout.
The Third line shows the
Tramline Target.
“Power On / Off“
Button
Turns the Artemis on
and off.
“Pre
-
Start”
This button starts the
metering motor running
to prime the seed pipes
prior to the drill entering
the ground or moving
forward.
“Tramline
+1 Bout” Button
This button will override the
current Tramline Count and add
1 bout the current Tramline
Bout.
“Setup” Button
Used to enter the
Setup/Configuration
Menu
“ENTER” Button
When you have typed
in a new Target Rate on
the RATE page, press
this button to enter it.
“SD/MMC Card
Reader”
“Forward Speed”
This displays the live
Forward Speed
Reading.
If the speed is too high
or too low then it will
alarm and show an
up/down arrow.
“Tramline Hold” Button
This will prevent the
tramline bout counting
o
n if the drill is lifted while
working in the field.
“Return to MAIN Screen”
Press at any time to return from the Rate screen or any other
screen, back to the ‘MAIN’ Artemis screen displayed here.
Press to swit
ch between Fan 1 & Fan 2 while on the MAIN page if
using twin fans.
Numeric Keypad
Used to enter a 'Target
Rate' while on RATE
page. If the Target Rate
displayed is incorrect,
just type in a new one,
finishing with the Enter
key.
Use also for k
eying in a
value within Setup
Menu.
“Seed/Fert Motor On / Off” Buttons
These buttons allow the metering motors to be
independently switched on or off.
These buttons will overr
ide the cut out status on the
drill.
“Fan Speed”
This is the Fan RPM
Speed.
If this drops below the
preset Alarm threshold
then the system will
alarm and the Metering
Motor will not run.

Summary

Artemis PSI Interface Overview

Tramline Bouts

Displays bout and side information for tramlines, showing current and target bout.

Forward Speed Display

Shows live forward speed with alarms for too high or too low speed.

Fan Speed Monitoring

Displays Fan RPM; alarms and stops motor if speed drops below threshold.

Return to Main Screen Function

Returns to the main Artemis screen from any other screen.

Numeric Keypad Input

Used for entering Target Rates and setup values via numerical input.

Enter Button Confirmation

Confirms entered Target Rates on the RATE page.

Setup Button Access

Accesses the Setup/Configuration Menu.

Power On;Off Control

Turns the Artemis unit on and off.

SD;MMC Card Reader

Slot for SD/MMC memory cards for data storage.

Pre-Start Function

Priming function for seed pipes before drilling begins.

Seed;Fert Motor Control

Independently control metering motors, overriding drill cut-out status.

Tramline Hold Button

Prevents tramline bout counting when drill is lifted.

Tramline +1 Bout Button

Manually increments the current tramline bout count by one.

Artemis PSI Operation Procedures

Product Calibration

Step-by-step guide for calibrating metering units for new products.

Altering Application Rate

Methods for changing the application rate via keypad or nudge buttons.

Tramline Configuration

Procedure for configuring tramline settings based on drill width.

Pre-Start Operation

Details on priming seed pipes and motor behavior during pre-start.

Overview

1. Device Overview and Interface
2. Display Elements
3. Keypad and Buttons
4. Product Calibration
5. Altering the Application Rate
6. Tramline Configuration
7. Pre-Start Functionality
8. Technical Specifications

The Artemis PSI is a precision farming device designed for automatic, variable-rate control of drills utilizing Accord-type metering units. It allows for manual override of predetermined rates based on field conditions.

Device Overview and Interface:

The device features a clear display and a user-friendly interface with several dedicated buttons and a numeric keypad.

Display Elements:

• "Tramline Bouts": This section displays the current tramline bout and target. Wheel marks indicate an active tramline bout and its side.
• "Forward Speed": Shows the live forward speed reading. An alarm with up/down arrows will activate if the speed is too high or too low.
• "Fan Speed": Displays the Fan RPM Speed. If this drops below a preset alarm threshold, the system will alarm, and the metering motor will not run.

Keypad and Buttons:

• Numeric Keypad: Used for entering a 'Target Rate' on the RATE page or values within the Setup Menu.
• "ENTER" Button: Confirms the entry of a new Target Rate on the RATE page.
• "Setup" Button: Accesses the Setup/Configuration Menu.
• "Power On / Off" Button: Turns the Artemis device on and off.
• "Pre-Start" Button: Initiates the metering motor to prime seed pipes before drilling or moving forward.
• "Seed/Fert Motor On / Off" Buttons: Independently switches metering motors on or off, overriding the drill's cut-out status.
• "Tramline Hold" Button: Prevents the tramline bout from counting on if the drill is lifted while working in the field.
• "Tramline +1 Bout" Button: Overrides the current Tramline Count and adds one bout.
• "Return to MAIN Screen": Returns to the 'MAIN' Artemis screen from any other screen. While on the MAIN page, it switches between Fan 1 and Fan 2 if twin fans are used.
• "SD/MMC Card Reader": For data storage and transfer.

Product Calibration:

Calibration is essential when a new product is introduced or the metering unit position is changed.

1. Setup: Configure the drill for a bucket test.
2. Priming: Locate and press the White priming button switch near the metering unit.
3. Metering: The motor will start metering out seed. Continue until a reasonable amount is metered.
4. Weighing: Weigh the product and record the weight in grams or kilograms.
5. Input: Return to the headunit and enter the dispensed weight.
6. Verification: After entering the weight, the Artemis displays the minimum and maximum achievable forward speeds. If these speeds are unsuitable for drilling conditions, adjust the metering unit and recalibrate.

Altering the Application Rate:

The application rate can be adjusted via the "RATE" button on the right side of the screen. This adjustment varies depending on whether a single or dual product system is in use.

• Direct Entry: Type a new rate using the numerical keypad and press the "Enter" button.
• "Nudge" Buttons: Use these buttons to alter the application rate by a pre-defined percentage.

Tramline Configuration:

Tramline configuration is adjusted through the "Setup" button, followed by selecting the "?" key. This displays a screen based on the drill width.

• Target Bouts: Increase or decrease the number of target bouts using the up and down arrows until the desired sprayer width is achieved.
• Symmetric/Asymmetric: The Left and Right buttons determine whether a Symmetric or Asymmetric Tramline sequence is used.

Pre-Start Functionality:

The "Pre-Start" button primes the seed pipes with seed before drilling. Pressing this button runs the motor for a preset time, simulating a specified speed. If the forward speed remains below 0.5 km/hr during this period, the motor stops until the drill moves or the "Pre-Start" button is pressed again.

Technical Specifications:

• Part Number: S/DC/500-10-731
• Issue: 1.00
• Date: 2/7/13
• Document Number: UK731100.DOC

The Artemis PSI is designed to enhance efficiency and precision in drilling operations by providing comprehensive control and monitoring capabilities.

RDS Pro Series Specifications